ISUZU ENGINE

Found 861 results

Select a filter to limit the results

Symptoms Air Filter Air Intake Tube Block Camshaft Computer Crankshaft Crankshaft Pulley Cylinder Head Dipstick Flexplate Flywheel Harmonic Balancer Identification Idle Air Control Intake Manifold Knock Sensor MAP Sensor Mass Air Flow Sensor Oil Oil Change Oil Cooler Oil Fill Cap Oil Filter Oil Pan Oil Pressure Sensor Oil Pump Oxygen Sensor Piston Rebuild Replace/Remove Serpentine Belt Starter Throttle Body Timing Belt Timing Chain Tune-up Turbo Vacuum Hose Diagram Wiring

How To Change The Timing Belt

Is There A Guide On How To Change The Timing Belt On A 2004 Rodeo Somewhere? Its 3.2l 4wd Engine. A Video Would Be Perfect But I Can't...

Asked by Kinetik74 ·

40 ANSWERS

27 IMAGES

2004

Turn Over an Engine by Hand | Bar Over

VIDEO

Turn Over an Engine by Hand | Bar Over

Instructional repair video

Code Reading

A check engine light, also known as a service engine light, or a MIL (malfunction indicator light) is designed to let you know there is a problem with one of your car's...

Cranks Wont Start

The Vehicle Cranks But Wont Start. I Have Replaced Both Cam Sensor. The Crankshaft Sensor And Battery. Per The Computer I Have 63psi Fuel...

Asked by Brian D Rumsey ·

30 ANSWERS

15 IMAGES

2004

Will Not Start

The Check Engine Light Was On. A Few Times It Would Not Start At All Unless I Opened The Hood And Then Closed It And Then Tried Again To...

Asked by storm1 ·

41 ANSWERS

1 VIDEO

15 IMAGES

2004

Camshaft Timing Procedure

Hi, Have A Recently Purchased This Vehicle With Direct Injection. I Have Learned They Were Only In Production The Last Ten Months Of The...

Asked by Ramoner1 ·

14 ANSWERS

1 VIDEO

25 IMAGES

2004

Camshaft Marks

I Need To Know The Positioning For The Pulleys On A 2.2l Engine. Replaced The Cam Sensor Put The Timing Belt Back On And Now The Vehicle Won...

Asked by ecfwire2 ·

53 ANSWERS

13 IMAGES

2002

Camshaft Position Sensor?

Can You Show Me Where The Camshaft Position Sensor Is Located?

Asked by Jols ·

35 ANSWERS

24 IMAGES

2004

P1000 Trouble

A P1000 code is designed to inform the driver the engine management system is not working to it's full potential. When in open loop, the powertrain management system is...

Engine In High Rev

Hi, I Am Working On This Vehicle With A 4jg21 Engine Equipped With An Electronic Version Injector Pump. The Issue With This Car Is...

Asked by Bataan Deireragea ·

17 ANSWERS

20 IMAGES

1995

Truck Will Not Start Without Starting Fluid

Truck Will Not Start Without Starting Fluid. I Put A New Fuel Pressure Limiter And A Fuel Pressure Regulator On It. I Also Put A New Pigtail...

Asked by BHuntley ·

3 ANSWERS

13 IMAGES

2008

Engine Wiring Diagrams Please?

I Get A Check Engine-reduced Power Lights After Engine Start. It Seems To Only Happen When Temperatures Are 40 Degrees Or Lower. The Engine...

Asked by mtnbiker ·

19 ANSWERS

13 IMAGES

2001

DRIVE BELT CHANGE - Serpentine Belt

I Was Driving My 2000 Isuzu Rodeo When My Drive Belt Broke And Found That The Bearings In A Pulley Were Totally Destroyed So I Replaced The...

Asked by mike2005 ·

34 ANSWERS

11 IMAGES

2000

Ask a new Isuzu question

Ask a Car Question. It's Free!

© 1999 - 2025 2CarPros, Inc.