1990 Ford Other transmission a4ld

Tiny
BADBOB1368
  • MEMBER
  • 1990 FORD
  • 2.9L
  • V6
  • 4WD
  • AUTOMATIC
  • 100,000 MILES
When you put it into gear you can hear engine bog down but no go in all forward and reverse gears. Used my obd tester got 5 codes dtc12, dtc26, dtc41, dtc77 all KOER 77 indicates operator error wot not senced did test three times still not senced. Dtc12 I checked IAC selinoid and valve ohms appropriate level and valve clean and working properly. CAN YOU HELP PLEASE THANK YOU FOR YOUR TIME Bob Moyer
Saturday, March 22nd, 2014 AT 7:15 PM

14 Replies

Tiny
HOMER1967
  • MECHANIC
  • 875 POSTS
What is the model of this vehicle?
Was this
answer
helpful?
Yes
No
Saturday, March 22nd, 2014 AT 7:34 PM
Tiny
BADBOB1368
  • MEMBER
  • 11 POSTS
BroncoII
Was this
answer
helpful?
Yes
No
Saturday, March 22nd, 2014 AT 7:39 PM
Tiny
BADBOB1368
  • MEMBER
  • 11 POSTS
Bronco II XLT
Was this
answer
helpful?
Yes
No
Saturday, March 22nd, 2014 AT 7:39 PM
Tiny
HOMER1967
  • MECHANIC
  • 875 POSTS
Ok, good.I'll do some research and let you know what I come up with
Was this
answer
helpful?
Yes
No
Saturday, March 22nd, 2014 AT 7:45 PM
Tiny
HOMER1967
  • MECHANIC
  • 875 POSTS
Is there a fifth code? Or is that all of them?
Was this
answer
helpful?
Yes
No
Saturday, March 22nd, 2014 AT 7:47 PM
Tiny
BADBOB1368
  • MEMBER
  • 11 POSTS
Thanks alot homer I appreciate you and your time!
Was this
answer
helpful?
Yes
No
Saturday, March 22nd, 2014 AT 7:48 PM
Tiny
BADBOB1368
  • MEMBER
  • 11 POSTS
01 is cyl:6 then says cylinder number
Was this
answer
helpful?
Yes
No
Saturday, March 22nd, 2014 AT 7:50 PM
Tiny
HOMER1967
  • MECHANIC
  • 875 POSTS
Your welcome badbob, the codes are basically for fuel control and 02 sensor issues. And I don't think they have anything to do with the truck not moving, it should move, maybe run like crap but move none the less. Have you checked the fluid level in the trans? If it is ok? Then you may have a severely clogged trans filter or a internal transmission issue
Was this
answer
helpful?
Yes
No
Saturday, March 22nd, 2014 AT 8:00 PM
Tiny
BADBOB1368
  • MEMBER
  • 11 POSTS
Just had transmission out pulled pan was pretty clean but changed filter anyway cheked 3-4 shift and lockup selonoids they tested good
Was this
answer
helpful?
Yes
No
Saturday, March 22nd, 2014 AT 8:04 PM
Tiny
BADBOB1368
  • MEMBER
  • 11 POSTS
Fluid is at appropriate level
Was this
answer
helpful?
Yes
No
Saturday, March 22nd, 2014 AT 8:05 PM
Tiny
HOMER1967
  • MECHANIC
  • 875 POSTS
You may have a bad pump, or a valve body issue.I would suggest that you take it to a tranny shop for a diagnosis.
Was this
answer
helpful?
Yes
No
Saturday, March 22nd, 2014 AT 8:09 PM
Tiny
BADBOB1368
  • MEMBER
  • 11 POSTS
Trying to save money ya know how that goes lol can I pull it back out and them bench test or do I need to have vehicle towed there
Was this
answer
helpful?
Yes
No
Saturday, March 22nd, 2014 AT 8:14 PM
Tiny
BADBOB1368
  • MEMBER
  • 11 POSTS
THANK YOU HOMER have a good shift
Was this
answer
helpful?
Yes
No
Saturday, March 22nd, 2014 AT 8:21 PM
Tiny
HOMER1967
  • MECHANIC
  • 875 POSTS
I think it would be best to take them the whole vehicle badbob. That was the can also test all the electronics. You are welcome and have a great night.
Was this
answer
helpful?
Yes
No
Saturday, March 22nd, 2014 AT 8:51 PM

Please login or register to post a reply.

Related Transmission Forward Content

VIEW MORE