2002 Honda Odyssey

Tiny
DB02ODYSSEY
  • MEMBER
  • 2002 HONDA ODYSSEY
  • 6 CYL
  • FWD
  • AUTOMATIC
  • 120,000 MILES
How do you replace the upper roller hinge assemblies in a 2002 odyssey? The rollers/guides seem to be shot in mine. Do I have to replace the cables at the same time?
Do you
have the same problem?
Yes
No
Monday, November 15th, 2010 AT 3:44 PM

4 Replies

Tiny
DR LOOT
  • EXPERT
ACS liding Door Latch Replacement NOTE:Put on gloves to protect your hands.
Remove these items: Door panel (see Sliding Door Panel Removal/Installation
Plastic cover, as necessary (see Component Location Index ) Remove the bolts (A) and the bolts (B). Disconnect the door latch cable (C). If equipped, disconnect the auto-close cable (D), lower roller lever cable (E), and power door closer connector (F). Then remove the latch (G) through the hole in the door. Fig. 32: Removing Bolts Courtesy of AMERICAN HONDA MOTOR CO, INC. Install the latch in the reverse order of removal, and note these items: Make sure the door locks and opens properly. If necessary, move the adjusting plate (A) to adjust the door latch cable (B) and the auto-close cable (C). Apply liquid thread lock to the adjusting plate mounting bolt (D) before reinstallation. When reinstalling the door panel, make sure the plastic cover is installed properly and sealed around its perimeter. Fig. 33: Moving Adjusting Plate Courtesy of AMERICAN HONDA MOTOR CO, INC. For EX and EX-L models: Re-home the power sliding doors (see RE-HOMING THE POWER SLIDING DOORS ).
Sliding Door Lower Roller Lever Replacement Power Sliding Door For EX and EX-L models: Disable the power sliding doors by turning off the main switch. Remove the nuts, then loosen the cable adjusting nuts (A) and disconnect the lower roller lever cable (B) from the lower roller lever (C). Take care not to bend the cable. Fig. 34: Loosening Cable Adjusting Nuts Courtesy of AMERICAN HONDA MOTOR CO, INC. Install the lower roller lever in the reverse order of removal, and note these items: Make sure the lower roller cable is connected properly. With the door fully open, make sure the power sliding door handle switch (D) makes a clicking sound as soon as the inner or outer door handle is pulled. If necessary, adjust the cable adjusting nuts. Check the sliding door operation. Make sure the sliding door operates properly when the outside handle is pulled (sliding door in the open position; the sliding door closes fully). You will have to send me your e-mail and I will send you the photos because the site at this time is not allowed download of photos
Was this
answer
helpful?
Yes
No
Monday, November 15th, 2010 AT 5:04 PM
Tiny
DR LOOT
  • EXPERT
The photos I e-mailed you should correspond with the letters on the instructions on my post
Was this
answer
helpful?
Yes
No
Tuesday, November 16th, 2010 AT 5:27 PM
Tiny
DR LOOT
  • EXPERT
Sorry about that I'm ready to send you photos if you still need them? Let me know.
Was this
answer
helpful?
Yes
No
Tuesday, November 23rd, 2010 AT 3:43 PM
Tiny
DR LOOT
  • EXPERT
Power Sliding Door For EX and EX-L models: Disable the power sliding doors by turning off the main switch. Remove the nuts, then loosen the cable adjusting nuts (A) and disconnect the lower roller lever cable (B) from the lower roller lever (C). Take care not to bend the cable. Fig. 34: Loosening Cable Adjusting Nuts Courtesy of AMERICAN HONDA MOTOR CO, INC. Install the lower roller lever in the reverse order of removal, and note these items: Make sure the lower roller cable is connected properly. With the door fully open, make sure the power sliding door handle switch (D) makes a clicking sound as soon as the inner or outer door handle is pulled. If necessary, adjust the cable adjusting nuts. Check the sliding door operation. Make sure the sliding door operates properly when the outside handle is pulled (sliding door in the open position; the sliding door closes fully).
Was this
answer
helpful?
Yes
No
-1
Tuesday, November 23rd, 2010 AT 10:25 PM

Please login or register to post a reply.

Related General Content

Drill Out a Bolt and Tap a Thread
VIDEO

Recommended Guides