Hello

Tiny
USERSORENTO
  • MEMBER
  • 2002 KIA SORENTO
  • 140,000 MILES
Hello. Our sorento crossed the river. After that time the ECU is changed. Also the fuel tank is cleaned from water, and engine injectors are changed. Motor CRDI 2.5. Yesterday the car was starting and working for 10=20minutes and more. Today again after ignition it turns off. What could be the problem?And what other places should be dried.
Tuesday, October 30th, 2012 AT 3:15 PM

11 Replies

Tiny
KHLOW2008
  • MECHANIC
  • 41,814 POSTS
The crank sensors. Check for trouble codes and it should tell you what to look for.
Was this
answer
helpful?
Yes
No
Tuesday, October 30th, 2012 AT 3:36 PM
Tiny
USERSORENTO
  • MEMBER
  • 7 POSTS
Sometimes starts at the first try sometimes after long time holding the start, and sometimes repeated trial can start the engine. Engine is CRDI. When started it automatically turns off after any time like one minute.
Was this
answer
helpful?
Yes
No
Wednesday, October 31st, 2012 AT 12:14 PM
Tiny
KHLOW2008
  • MECHANIC
  • 41,814 POSTS
Have you checked for trouble codes?
Was this
answer
helpful?
Yes
No
Wednesday, October 31st, 2012 AT 12:17 PM
Tiny
USERSORENTO
  • MEMBER
  • 7 POSTS
There is no Code error. In the diagnostics there is no trouble. Check engine light is working properly. As I mentioned the ECU is changed. Could it be the problem.
Was this
answer
helpful?
Yes
No
Wednesday, October 31st, 2012 AT 1:24 PM
Tiny
KHLOW2008
  • MECHANIC
  • 41,814 POSTS
If the ECU is similar to the original one, it should not be the problem.

We don't have any information on your vehicle engine system so I don't know what sensors are at the lower end of the engine apart from the crank sensor. Have you checked that yet?

You might need to have the scan tool go through the various sensors to see if any is working out of specs.
Was this
answer
helpful?
Yes
No
Wednesday, October 31st, 2012 AT 4:56 PM
Tiny
USERSORENTO
  • MEMBER
  • 7 POSTS
http://sorento.kia-club.ru/Repair_manual/download/DOWN/BL%20Engine.pdf this engine CRDI 2.5
Was this
answer
helpful?
Yes
No
Thursday, November 1st, 2012 AT 6:08 AM
Tiny
KHLOW2008
  • MECHANIC
  • 41,814 POSTS
Cranksensor CKP, Page 94. Is the one you should look at. Accelerator pedal position sensor too if water had gotten into the cabin.
From the files, you can look through all the sensors and if any was submerged, you need to check those.
Was this
answer
helpful?
Yes
No
Thursday, November 1st, 2012 AT 12:33 PM
Tiny
USERSORENTO
  • MEMBER
  • 7 POSTS
Ok thank you. I will try them
Was this
answer
helpful?
Yes
No
Thursday, November 1st, 2012 AT 2:10 PM
Tiny
KHLOW2008
  • MECHANIC
  • 41,814 POSTS
You're welcome and good luck.

When checking sensors, ensure the connectors are clean as water contamination can cause problems and have the charging tested as well. Improper voltage can cause sensors to fail to work correctly. Codes might not appear as some codes needs more than 1 trip to be recorded.
Was this
answer
helpful?
Yes
No
Thursday, November 1st, 2012 AT 5:21 PM
Tiny
USERSORENTO
  • MEMBER
  • 7 POSTS
Changed the ckp sensor with another cars used one . after that before starting pressure was low then cleaned the HP pump, later the condition is like http://www.youtube.com/watch?v=V2cGCPFHnW0&feature=youtu.be

pressure is measured by the tool for CRDI that was said to be ok. is there any nuances to measure the pressure properly ? should all the vacuum lines closed before starting engine ?
Was this
answer
helpful?
Yes
No
Friday, November 2nd, 2012 AT 2:49 PM
Tiny
KHLOW2008
  • MECHANIC
  • 41,814 POSTS
What vacuum lines are you refering to?
The condition seems to indicate a fault with the fuel pressure or injection pump. Did you monitor the fuel pressure with a scan tool?

Since you were able to start the engine briefly, did you recheck for trouble codes?

Was the accelerator pedal position sensor affected by water?
Was this
answer
helpful?
Yes
No
Friday, November 2nd, 2012 AT 3:12 PM

Please login or register to post a reply.

Sponsored links