97 Intrepid stalling when warm

Tiny
J.STIEG
  • MEMBER
  • 1997 DODGE INTREPID
  • 180,000 MILES
Stalls when warm resulting in a no spark condition.
Others saw shorting in wire harness, repaired harness and problem still exist.

Suspect fault in cam sensor or PCM, Can I do a check on the cam sensor for a start?
Wednesday, April 11th, 2012 AT 9:49 PM

14 Replies

Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
How long will it not start for when it gets hot?ALso any codes set in the computer?
Was this
answer
helpful?
Yes
No
Wednesday, April 11th, 2012 AT 9:57 PM
Tiny
J.STIEG
  • MEMBER
  • 352 POSTS
After about 20 min it starts and runs fine for a little while.
All I get for a code is p0137 o2 low volts bank1 sen2, probably not related.
Was this
answer
helpful?
Yes
No
Wednesday, April 11th, 2012 AT 10:11 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
No that wouldnt be related to no spark.
Was this
answer
helpful?
Yes
No
Wednesday, April 11th, 2012 AT 10:40 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
What size engine do you have?
Was this
answer
helpful?
Yes
No
Wednesday, April 11th, 2012 AT 10:48 PM
Tiny
J.STIEG
  • MEMBER
  • 352 POSTS
What do you think, maybe cam sensor.
Was this
answer
helpful?
Yes
No
Wednesday, April 11th, 2012 AT 10:48 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
What size engine do you have?I was thinking crank shaft position sensor.
Was this
answer
helpful?
Yes
No
Wednesday, April 11th, 2012 AT 10:57 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
Also do you have a scan tool that will read live engine data?
Was this
answer
helpful?
Yes
No
Wednesday, April 11th, 2012 AT 11:08 PM
Tiny
J.STIEG
  • MEMBER
  • 352 POSTS
3.3 liter engine
Was this
answer
helpful?
Yes
No
Thursday, April 12th, 2012 AT 2:34 PM
Tiny
J.STIEG
  • MEMBER
  • 352 POSTS
Ok, I let it run and waited for it to quit, after it quit I checked a few things and found out there was no spark and no injector pulse.
But then I came back to wire harness and jiggled it and car started jiggled it some more and quit again kept doing it and it kept starting and quitting, now I need to replace cam sensor or wiring harness.

Can you post some wiring diagrams of the cam sensor.
Was this
answer
helpful?
Yes
No
Thursday, April 12th, 2012 AT 3:26 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
Can I get your email address so I can email you some wire diagrams would work out better that way.
Was this
answer
helpful?
Yes
No
Thursday, April 12th, 2012 AT 5:49 PM
Tiny
J.STIEG
  • MEMBER
  • 352 POSTS
J. Stieg@yahoo. Com
Was this
answer
helpful?
Yes
No
Thursday, April 12th, 2012 AT 10:10 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
So the connector at the cam sensor is the wires your jiggling to make it start?
Was this
answer
helpful?
Yes
No
Thursday, April 12th, 2012 AT 11:21 PM
Tiny
J.STIEG
  • MEMBER
  • 352 POSTS
Yes, I might have to get the cam sensor it has 8'' of wire on it that could be bad, I replaced the wire connector on the engine side of the harness and there was no change.
Was this
answer
helpful?
Yes
No
Friday, April 13th, 2012 AT 3:20 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
Sound like it could very well be the pig tail off the cam sensor. Over time engine vibration breaks the wire inside the insulation so its hard to find the broken wire sometimes.
Was this
answer
helpful?
Yes
No
Friday, April 13th, 2012 AT 5:22 PM

Please login or register to post a reply.

Sponsored links