Rear axle seal and bearing

Tiny
ANGELSCOTHHH
  • MEMBER
  • 2001 JEEP GRAND CHEROKEE
  • V8
  • 4WD
  • AUTOMATIC
I need to know how to replace a rear axle seal and bearing on my vehicle (limited edition)? Cannot bring to shop for the third time. Please help.
Tuesday, June 21st, 2011 AT 10:32 PM

11 Replies

Tiny
MHPAUTOS
  • MECHANIC
  • 31,937 POSTS
Do you have access to a hydraulic press to remove the bearing? Has this been done by a work shop and it is still faulty? If so they should warranty their work.
Was this
answer
helpful?
Yes
No
Tuesday, June 21st, 2011 AT 10:38 PM
Tiny
ANGELSCOTHHH
  • MEMBER
  • 16 POSTS
No I do not think so. My husband will be doing it. Have brought it in three times in five years and just cannot afford to bring it in again. He is worried about if he has to remove gas tank to do it and just how exactly to do it? He has worked on cars all his life but is unsure about this vehicle.
Was this
answer
helpful?
Yes
No
Tuesday, June 21st, 2011 AT 10:40 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,758 POSTS
Axle shafts removal:

1. Place transmission in neutral.
2. Raise and support vehicle.
3. Remove wheel and tire assembly.
4. Remove brake caliper and rotor.
5. Remove nuts holding axle retainer plate to axle tube from the rear of the axle flange.
6. Pull axle shaft from the axle with Slide Hammer 7420 and Adapter 6790. Mount the adapter to the axle with lug nuts.

NOTE: It is normal that the axle bearing race is loose in the axle tube.

INSTALLATION

1. Install axle into the axle tube with the flat area of the retainer plate upward.
2. Insert retaining plate studs into the brake backing plate and axle tube flange.
3. Install retainer nuts and tighten nuts to 61 Nm (45 ft. Lbs.).
4. Install the brake caliper and rotor.
5. Install wheel and tire.
6. Check and fill the differential with gear lubricant.
7. Lower vehicle.

AXLE BEARINGS/SEALS
REMOVAL

1. Remove axle shaft from vehicle.

NOTE: It is normal that the axle bearing race is loose in the axle tube.

2. Drill a shallow hole into soft steel axle bearing retaining ring with a 3/8 inch drill bit (Fig. 26). Use a drill depth stop to avoid marking the axle.

3. With a cold chisel cut the retaining ring across drilled hole. (Fig. 27)
4. Slide retaining ring from axle shaft.

5. Remove axle bearing from the shaft with, a press and Splitter 1130 placed between the seal and bearing (Fig. 28).
6. Remove seal from axle.
7. Remove retaining plate from axle shaft.

INSTALLATION

1. Verify axle shaft retaining plate is flat with a straight edge.

NOTE: If the plate is warped or the studs are loose in the plate replace the retaining plate.

2. Install retaining plate on the axle shaft (Fig. 29).
3. Apply a coat of multi-purpose grease on sealing surface of axle seal.
4. Install seal on the axle shaft with cavity away from retaining plate (Fig. 29).
5. Lubricate bearing with Mopar(R) Wheel Bearing Grease or equivalent. Wipe excess grease from the bearing.

6. Install bearing on the axle shaft with Installer 7913 and a press (Fig. 30).

7. Press soft metal retaining ring onto axle shaft with Installer 7913 and a press (Fig. 31).
8. Install axle in vehicle.
Was this
answer
helpful?
Yes
No
+9
Tuesday, June 21st, 2011 AT 10:41 PM
Tiny
ANGELSCOTHHH
  • MEMBER
  • 16 POSTS
Okay, thank you very very much. I appreciate it a lot. Have a wonderful day and thanks again!
Was this
answer
helpful?
Yes
No
Tuesday, June 21st, 2011 AT 10:44 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,758 POSTS
I seriously doubt that he is going to be equipped to do this himself.
Was this
answer
helpful?
Yes
No
-3
Tuesday, June 21st, 2011 AT 10:45 PM
Tiny
ANGELSCOTHHH
  • MEMBER
  • 16 POSTS
His buddy has a lot of tools. All he does is work on vehicles and stuff. I am sure and hopeful that they can get it done. We will see, but it was nice to get the information to know for sure what to do. Thanks again. I will have him look at this when he gets home and if he has questions I will have him write. Thanks
Was this
answer
helpful?
Yes
No
+1
Tuesday, June 21st, 2011 AT 10:50 PM
Tiny
MHPAUTOS
  • MECHANIC
  • 31,937 POSTS
You can always just send the axle to a work shop to do the bearing change, and do the rest at home.
Was this
answer
helpful?
Yes
No
+1
Tuesday, June 21st, 2011 AT 10:55 PM
Tiny
ANGELSCOTHHH
  • MEMBER
  • 16 POSTS
So does he have to take the differential cover off to get to the retainer plate? Which means take the gas tank out? Like a Chevrolet truck.
Was this
answer
helpful?
Yes
No
Tuesday, June 21st, 2011 AT 11:03 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,758 POSTS
No, this one is all done from the wheel end. The big problem is that the bearings are pressed onto the axle and will require a hydraulic press to get them off and the new ones on.
Was this
answer
helpful?
Yes
No
+2
Tuesday, June 21st, 2011 AT 11:07 PM
Tiny
ANGELSCOTHHH
  • MEMBER
  • 16 POSTS
Okay, I will let him know. He will be home late but sure he will have questions. Thanks
Was this
answer
helpful?
Yes
No
Tuesday, June 21st, 2011 AT 11:10 PM
Tiny
ANGELSCOTHHH
  • MEMBER
  • 16 POSTS
He says, thanks for the help.
Was this
answer
helpful?
Yes
No
Wednesday, June 22nd, 2011 AT 12:57 AM

Please login or register to post a reply.

Sponsored links