How do I change speedo cable

Tiny
ANONYMOUS
  • MEMBER
  • 2000 HYUNDAI ATOS
How do I change speedo cable
Tuesday, October 23rd, 2012 AT 5:50 PM

12 Replies

Tiny
KHLOW2008
  • MECHANIC
  • 41,814 POSTS
Note routing of the cable.
Disconnect the end at transmission.
Remove the meter cluster.
Disconnect the cable and pull cable out. Install new cable making sure the cable is not subjected to tight bends.
Was this
answer
helpful?
Yes
No
+2
Tuesday, October 23rd, 2012 AT 7:01 PM
Tiny
LASZLO CSONKA
  • MEMBER
  • 13 POSTS
Hey, guys.
I would like to inquire about:
I have a vintage 2000 Hyundai Atos car.
What could be the problem?
Cold always immediately wants to suffocate and consumption of 5.5 liters, 7.5 liters increased.
Someone has met with that?
Sorry if I wrote the wrong question!

Laci
Was this
answer
helpful?
Yes
No
Tuesday, October 8th, 2013 AT 9:39 AM
Tiny
KHLOW2008
  • MECHANIC
  • 41,814 POSTS
Check the cold start system. Could be the IAC and throttle body needs cleaning.
Was this
answer
helpful?
Yes
No
Wednesday, October 23rd, 2013 AT 8:37 AM
Tiny
LASZLO CSONKA
  • MEMBER
  • 13 POSTS
Greetings!
I would like to inquire.
I have a ELM327 interface device.
Is there a chance to join the Hyundai Matrix?
Or what software should be added or cable?
I would like to see what mistakes you could store.
There is no check engine lights, this 2000 vintage.

Laci
Was this
answer
helpful?
Yes
No
Thursday, January 30th, 2014 AT 8:49 AM
Tiny
LASZLO CSONKA
  • MEMBER
  • 13 POSTS
I'm sorry, misspelled the interpreter.
Hyundai atos
Was this
answer
helpful?
Yes
No
Thursday, January 30th, 2014 AT 9:23 AM
Tiny
KHLOW2008
  • MECHANIC
  • 41,814 POSTS
Unless it is a carburetted engine, otherwise there should be a check engine light.
Was this
answer
helpful?
Yes
No
Thursday, January 30th, 2014 AT 7:47 PM
Tiny
LASZLO CSONKA
  • MEMBER
  • 13 POSTS
No carburetor. But there is no check engine light.
ELM327 interface could not communicate with him.
I tried a couple of software.
Ecu connection throws out
Was this
answer
helpful?
Yes
No
Friday, January 31st, 2014 AT 11:30 AM
Tiny
KHLOW2008
  • MECHANIC
  • 41,814 POSTS
If the Check Engine Light do no come on when ignition switch is turned on, you need to check the circuit first. It could be a missing power supply. If you mean the check engine light do not indicate any fault and the scan tool or software you use is not communicating, then you need to get the correct software and/or scan tool.

If the scan tool has a feature for OBD-II, use it instead of going for specific model/make.
Was this
answer
helpful?
Yes
No
Friday, January 31st, 2014 AT 5:01 PM
Tiny
LASZLO CSONKA
  • MEMBER
  • 13 POSTS
I looked at the check lamp on the instrument panel.
But there's no place glowing.
The panel on the right, but have no power over it.
I guess it was not in advance.
To do this, what kind of software would be compatible?
Where could I look?
Or is it the ELM327 interface to be good?
As I watched the basis of pin ISO9141 protocol to communicate with the car.
Was this
answer
helpful?
Yes
No
Saturday, February 1st, 2014 AT 12:57 AM
Tiny
KHLOW2008
  • MECHANIC
  • 41,814 POSTS
I am not sure which protocol is the one you require but if the dash does not have any Chceck engine Light, you need to get it working first. It could be a power supply or ECM fault.
Was this
answer
helpful?
Yes
No
Saturday, February 1st, 2014 AT 5:20 AM
Tiny
LASZLO CSONKA
  • MEMBER
  • 13 POSTS
How to power?
Or ecm?
I wrote that the ecu is not connected to long runs nicely
check engine light is not because there is no lamp nor place, that slot.
Was this
answer
helpful?
Yes
No
Saturday, February 1st, 2014 AT 5:47 AM
Tiny
LASZLO CSONKA
  • MEMBER
  • 13 POSTS
Or does anyone have experience with that for the 2000 vintage, which correspond to a code reader?
327 Elm find the ISO9141 protocol, and then prints that you can not find OBD2 system.
I have tried many kinds of software are.

Hi Laci
Was this
answer
helpful?
Yes
No
Tuesday, February 4th, 2014 AT 1:38 PM

Please login or register to post a reply.

Sponsored links