engine just quit running and now it won't start

1997 PONTIAC SUNFIRE
10,000 MILES
Avatar
FRANK L
  • MEMBER
  • 4 POSTS
I have a 97 sunfire quit running and wont start. I put new map sensor have good spark wont run on starting fluid either what else could cause not to start? I have checked timing getting spark wont start on starting fluid? What should I check next?
Jan 9, 2012 at 2:01 AM
Advertisement
Avatar
SATURNTECH9
  • CAR REPAIR CONTRIBUTOR
  • 30,869 POSTS
Do you have any codes?Have you checked compression yet?
Jan 9, 2012 at 2:15 AM
Avatar
FRANK L
  • MEMBER
  • 4 POSTS
no codes compression seems goods no gage to check. it was like it was running out of gas then died and wont even try to fire
Jan 9, 2012 at 2:21 AM
Avatar
SATURNTECH9
  • CAR REPAIR CONTRIBUTOR
  • 30,869 POSTS
You cant assume compression is good auto zone rents compression testers and they also rent fuel pressure gauges rent both test them and post the results.
Jan 9, 2012 at 2:24 AM
Avatar
FRANK L
  • MEMBER
  • 4 POSTS
woundring y it wont run on starting flued getting spark should fire
Jan 9, 2012 at 2:30 AM
Avatar
FRANK L
  • MEMBER
  • 4 POSTS
ok thank u for your time what should compression b on a 2.2
Jan 9, 2012 at 2:32 AM
Avatar
SATURNTECH9
  • CAR REPAIR CONTRIBUTOR
  • 30,869 POSTS
Low compression and engine out of time.Let me know the compression and the fuel pressure reading.
Jan 9, 2012 at 2:41 AM
Avatar
CHAZ1983
  • MEMBER
  • 39 POSTS
my sunfire doing same thing i changed fuel filter crank sensor an igntion module an coils still same problem did u ever fix your or found out n e thing helpful
Jan 12, 2012 at 5:49 AM
Avatar
CHAZ1983
  • MEMBER
  • 39 POSTS
i should add one thing i got a ignition moduler off my aucle that was took off a used engine that ran an since i was lost couldnt find out why it aint running i took the used moduler to advance they tested it an said it failed two things idk my original one failed 3 things got another one from my auncle an it failed its weird they both came off runing cars is advance test wrong or do i just need to spend the 300.00 for a new moduler i realy dont got 300 bucks to spend but if thats what it takes to fix my car than i got no choice but weird thing is i have spark an everything with all 3 igntions i tryed if it was realy bad it just seems like there should be spark my car should start at all
Jan 24, 2012 at 3:17 AM
Avatar
CHAZ1983
  • MEMBER
  • 39 POSTS
i should add one thing i got a ignition moduler off my aucle that was took off a used engine that ran an since i was lost couldnt find out why it aint running i took the used moduler to advance they tested it an said it failed two things idk my original one failed 3 things got another one from my auncle an it failed its weird they both came off runing cars is advance test wrong or do i just need to spend the 300.00 for a new moduler i realy dont got 300 bucks to spend but if thats what it takes to fix my car than i got no choice but weird thing is i have spark an everything with all 3 igntions i tryed if it was realy bad it just seems like there should be spark my car shouldnt start at all
Jan 24, 2012 at 3:18 AM
Repair Safety Notice: This information is for general instructional purposes only. Vehicle repair can be dangerous. Verify all information, follow manufacturer service procedures, use proper tools and safety equipment, and consult a qualified repair shop when needed.