Where is the idle air control motor located?

Tiny
L2WO4OUR
  • MEMBER
  • 1991 CADILLAC BROUGHAM
  • 159,000 MILES
In a 1991 Cadillac brougham 5.7. I know its in the throttle, but I cant find it. Need the exact location need exact location of idle air control motor. Picture would help too.
Saturday, June 30th, 2012 AT 4:54 AM

15 Replies

Tiny
ASEMASTER6371
  • MECHANIC
  • 52,797 POSTS
Round housing with a 4 wire connector on the throttle body.

Why are you replacing it?

Roy
Was this
answer
helpful?
Yes
No
Saturday, June 30th, 2012 AT 4:45 PM
Tiny
L2WO4OUR
  • MEMBER
  • 20 POSTS
Roy im replacing it because my car turns off on idle. It always turns back on for like 3 seconds then it just turns off. I happen to believe maybe its the idle air control motor. Any suggestions?
Was this
answer
helpful?
Yes
No
Saturday, June 30th, 2012 AT 5:23 PM
Tiny
L2WO4OUR
  • MEMBER
  • 20 POSTS
Wrenchtech thanks you so much that was very helpful.
Was this
answer
helpful?
Yes
No
Saturday, June 30th, 2012 AT 5:24 PM
Tiny
ASEMASTER6371
  • MECHANIC
  • 52,797 POSTS
I would check for vacuum leaks at the base as the base gasket is a common failure for this issue.

Make sure the egr valve is not stuck open causing a massive vacuum leak.

And lastly, it could be the valve but can be tested with a scan tool to manually operate it.

Roy
Was this
answer
helpful?
Yes
No
Saturday, June 30th, 2012 AT 5:26 PM
Tiny
L2WO4OUR
  • MEMBER
  • 20 POSTS
*UPDATE* I already changed the idle air control valve (IAC) and the EGR valve and also the throttle position sensor along with the pcv valve. I put all these parts new and it still does the same thing. The car always turns on but turns off after 3 seconds. I dont know if its either a leak or something causing it to choke. It also drains the battery I always have to jump start it to turn it on every time. Please help.
Was this
answer
helpful?
Yes
No
Monday, July 2nd, 2012 AT 8:00 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,758 POSTS
Have you tested the fuel pressure?
Was this
answer
helpful?
Yes
No
Monday, July 2nd, 2012 AT 8:23 PM
Tiny
L2WO4OUR
  • MEMBER
  • 20 POSTS
No I havent not yet
Was this
answer
helpful?
Yes
No
Monday, July 2nd, 2012 AT 8:34 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,758 POSTS
That probably should have been the first thing you did.
It has to be 9-13PSI
Was this
answer
helpful?
Yes
No
Monday, July 2nd, 2012 AT 8:39 PM
Tiny
L2WO4OUR
  • MEMBER
  • 20 POSTS
So I checked the fuel pressure and its good I even changed the fuel filter. What I did notice was that the car only stays on when I disconnect the hose that runs from the back of the throttle to the map sensor, once I connect it back to the throttle the car shakes and it turns off. So I'm thinking maybe I have a bad MAP sensor, so I go and replace it brand new and it still does the same thing. It only stays on when I disconnect the hose from the throttle that goes to the MAP sensor. What could this be? And after I replaced the MAP sensor the check engine light went off. So I dont know what to do anymore? Any suggestions?
Was this
answer
helpful?
Yes
No
Tuesday, July 10th, 2012 AT 10:56 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,758 POSTS
Try unplugging the the electrical plug for the MAP sensor and see if it will run any better.
Was this
answer
helpful?
Yes
No
+1
Tuesday, July 10th, 2012 AT 11:08 PM
Tiny
L2WO4OUR
  • MEMBER
  • 20 POSTS
Ok ill try that now. What will that do or what?
Was this
answer
helpful?
Yes
No
Tuesday, July 10th, 2012 AT 11:33 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,758 POSTS
That will force the computer to default to a predetermine setting.
Was this
answer
helpful?
Yes
No
Tuesday, July 10th, 2012 AT 11:35 PM
Tiny
L2WO4OUR
  • MEMBER
  • 20 POSTS
I did that and the car turned off. So what I ended up doing was checking the check engine light manually (since the light came on again) and it gives me code #34 map sensor signal out of range, low. So what do I do now?
Was this
answer
helpful?
Yes
No
Wednesday, July 11th, 2012 AT 4:01 AM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,758 POSTS
Clear the code and start over. You triggered that code when you unplugged it. Try starting it after it is unplugged.
Was this
answer
helpful?
Yes
No
Wednesday, July 11th, 2012 AT 9:46 AM
Tiny
L2WO4OUR
  • MEMBER
  • 20 POSTS
So I ended up replacing the ECM and its not giving me the map sensor code anymore. But it is giving me code 22 which is tps sensor low signal. The sensor is brand new why would this be happening? I tested the sensor out and it is getting enough voltage and ground from the ECM but its not sending its signal back to ECM. What can I do?
Was this
answer
helpful?
Yes
No
Friday, July 27th, 2012 AT 4:33 PM

Please login or register to post a reply.

Sponsored links