Ford Ranger Questions
- 2003 Ford Ranger Engine Problem with 136000 miles
- I have a 2003 Ford Ranger 3.0 V6 Auto trans `136,000 miles After engine warms up Put into Park AC is running Idle will sometimes strat...
- Asked by lbm65 about 8 months ago - 2 Answers
- 2003 Ford Ranger problem
- I have a 2003 ford ranger with a 2.3L engine in it 4 cylinder. It started to make a clicking/knocking noise. It would only make that noise ...
- Asked by angelasegura about 8 months ago - 1 Answer
- 1998 Ford Ranger Engine Problem with 13500 miles
- Have a 4.0 v6 ohv 98 ford ranger with 135,000 miles. Truck idles rough and bucks. When pushing lightly on gas hesitates and stumbles. No ...
- Asked by badmechanic2 about 8 months ago - 1 Answer
- 1994 Ford Ranger Drivetrain Problem
- Hi this is justin i writing you again about my 1994 ford ranger with a 4.0 and with a automatic transmission 2wd i wrote about my problem ...
- Asked by jrh1986 about 9 months ago - 5 Answers
- 1994 Ford Ranger Engine Problem with 200000 miles
- So this is the second time I have posted on this topic. I have run through all the previously suggested tests and I'm still having the same ...
- Asked by Craig jaster about 9 months ago - 18 Answers
- 1991 Ford Ranger Heater Problem with 497896 miles
- I have a 1991 ford ranger 2.3L 5 speed. The heater has not worked very well only blowing mildly warm air. I just replaced the hea gasket,...
- Asked by Ronson about 9 months ago - 1 Answer
- 1994 Ford Ranger Drivetrain Problem with 300000 miles
- I replaced a clutch plate, something I have done many times. I used jack stands and brut force to remove the transmission. After the work ...
- Asked by terrypold about 9 months ago - 1 Answer
- 2001 Ford Ranger problem with 160000 miles
- 2001 Ranger XLT 4X4 I am doing this for a friend. He wants to replace the cruise control switches on his truck. When the air bag and cover ...
- Asked by aceshigh717 about 9 months ago - 1 Answer
- 1994 Ford Ranger Engine Problem with 200000 miles
- Ok, so my truck has been running pretty rough here lately, I have replaced the plugs and wires, mass air flow sensor, Ignition coil, and ran...
- Asked by Craig jaster about 9 months ago - 11 Answers
- 1989 Ford Ranger problem
- When i am working under a car or pickup i need a good work light.
- Asked by joe1953 about 9 months ago - 4 Answers
- 1989 Ford Ranger Engine Problem
- The engine will crank but will not start fire is getting to the spark plugs but i don't hear the fuel pump run, it was starting before i ...
- Asked by joe1953 about 9 months ago - 1 Answer
- 1994 Ford Ranger Drivetrain Problem
- Hi I have a 1994 Ford ranger with a 4.0 and a A4ld transmission 2wd my problem is my truck dies when putting in reverse and drive one day I ...
- Asked by jrh1986 about 9 months ago - 6 Answers
- 1989 Ford Ranger Engine Problem
- When the engine is cranking it shake real bad.
- Asked by joe1953 about 9 months ago - 3 Answers
- 1989 Ford Ranger problem
- When i push the line into the slave cylinder it wan't push in far enough seem like the clip have something to do with it but any way the ...
- Asked by joe1953 about 9 months ago - 11 Answers
- 1989 Ford Ranger problem
- When i push the hydraulic line into the slave cylinder it suppose to lock in place but when i pull on the line a little it will come out, ...
- Asked by joe1953 about 9 months ago - 6 Answers
- 1993 Ford Ranger Engine Problem with 20000 miles
- My Ranger does not want to start. It will crank over but not start. I JUST PUT A NEW FUEL PUMP IN. DOES IT HAVE BAD GAS IN IT LIKE ...
- Asked by pamelawahlig about 9 months ago - 1 Answer
- 1989 Ford Ranger problem
- The end that go into slave cylinder look like a plunger, do fluid open the plunger, or how do the plunger work.
- Asked by joe1953 about 9 months ago - 3 Answers
- 1989 Ford Ranger problem
- I have replace the slave cylinder, the clutch master cylinder, and the Hydraulic line, when i try to bleed the slave cylinder, no fluid or ...
- Asked by joe1953 about 9 months ago - 5 Answers
- 1989 Ford Ranger problem
- When i fill the reservoir with brake fluid, i can see fluid running out the line at the end that go into slave cylinder with it disconnect.
- Asked by joe1953 about 9 months ago - 5 Answers
- 1996 Ford Ranger Air_conditioner Problem with 41000 miles
- I have a 1996 ford ranger that I recently had the AC serviced on.Sometimes it will come on and work usually when you first start the vehicle...
- Asked by Ronson about 9 months ago - 3 Answers
- 1989 Ford Ranger problem
- I want to try to replace my clutch master.
- Asked by joe1953 about 9 months ago - 1 Answer
- 1989 Ford Ranger problem
- I have replace a new clutch master cylinder and slave cylinder,
- Asked by joe1953 about 9 months ago - 1 Answer
- 1994 Ford Ranger Drivetrain Problem
- Hi i have a 1994 ford ranger with a 4.0 with a automatic transmission i have a problem my truck drove just fine when i was heading home i ...
- Asked by jrh1986 about 9 months ago - 3 Answers
- 1989 Ford Ranger problem
- I can't use a brake line to flush the system out because the fluid lines on the clutch master cylinder/slave cylinder/Reservoir don't thread...
- Asked by joe1953 about 9 months ago - 5 Answers
- 1997 Ford Ranger Engine Problem with 180000 miles
- My Ford will not start first time. The accelerator must be pumped once, crank,it will try to start. Pump, crank, try to start. After 6 or 7 ...
- Asked by billtoothman about 9 months ago - 1 Answer
- 1989 Ford Ranger problem
- My slave cylinder was leaking so i try some power steerling stop leak, so i have replace the slave cylinder, now i need to flush the clutch ...
- Asked by joe1953 about 9 months ago - 6 Answers
- 1997 Ford Ranger problem
- 1997 ford xlt ranger 2x4 will start but won't stay running unless pumping gas. rondomly will idle for about 20 seconds [pur like a kitten] ...
- Asked by keithbates about 9 months ago - 4 Answers
- 1989 Ford Ranger problem
- I just replace a slave cylinder now i need to bleed it.
- Asked by joe1953 about 9 months ago - 3 Answers
- 2000 Ford Ranger Drivetrain Problem with 96000 miles
- I'm not sure if this type of pressure plate is compatable with a hydrolic clutch or not? My understanding that the original plates are self ...
- Asked by bkj228 about 9 months ago - 2 Answers
- 1989 Ford Ranger Drivetrain Problem
- I am puting the tranmission back in but having trouble getting the bolts started, is there a easy way.
- Asked by joe1953 about 9 months ago - 5 Answers
- 1991 Ford Ranger problem with 160000 miles
- I have a 1991 ford ranger. It's getting fuel and spark but won't start. What should I check?
- Asked by Steveashton about 9 months ago - 1 Answer
- 2000 Ford Ranger Engine Problem with 134643 miles
- I have a 2000 model for ranger 4.0 5spd. First thing in the morning, it will start fine. I can drive it for a few miles and turn it off, and...
- Asked by lewindillsyahoocom about 9 months ago - 1 Answer
- 1989 Ford Ranger Drivetrain Problem
- Or will it make any differant about putting scars on the crankshaft where the pilot roller bearing go.
- Asked by joe1953 about 9 months ago - 1 Answer
- 1998 Ford Ranger Suspension Problem with 60288 miles
- Two weeks ago, i had lower ball joints installed and an alignment on my truck,after that, it pulled to the left a little, took it back and ...
- Asked by 98rangerxlt about 9 months ago - 2 Answers
- 2000 Ford Ranger Engine Problem with 200000 miles
- I am looking at a 2000 Ford Ranger Ext Cab 4X2 3.0V6 Automatic. The truck has 200,000 miles but the truck looks new. If it has been well ...
- Asked by worthin52 about 9 months ago - 1 Answer
- 1989 Ford Ranger Drivetrain Problem
- I am trying to remove a clutch pilot bearing, the cluth pilot bearing is torn apart i want to know how can i take it out can i use a chisel ...
- Asked by joe1953 about 9 months ago - 3 Answers
- 1989 Ford Ranger Drivetrain Problem
- The bearing look like it is torn up how can get it out.
- Asked by joe1953 about 9 months ago - 8 Answers
- 1989 Ford Ranger Drivetrain Problem
- What you mean about pack it up wheel bearing and select a tight fit driver and pound it out what is a tight fit driver, the bearing look ...
- Asked by joe1953 about 9 months ago - 2 Answers
- 1989 Ford Ranger Drivetrain Problem
- I am trying to remove a pilot bearing with a pilot bearing tool, the tool want catch or hook under the bearing, when the bearing was replace...
- Asked by joe1953 about 9 months ago - 14 Answers
- 1989 Ford Ranger Drivetrain Problem
- Do i need a special tool, do i need to put oil or grease on the bearing. do i press the pilot bearing in with a special tool.
- Asked by joe1953 about 9 months ago - 1 Answer
- 1994 Ford Ranger Electrical Problem
- Hi I need help about my gas tank I need to know how many gallons I have on my 1994 Ford ranger xlt regular cab with a 4.0 and a automatic ...
- Asked by jrh1986 about 9 months ago - 1 Answer
- 1989 Ford Ranger Drivetrain Problem
- When i fill clutch master cylinder up with fluid i can see it running out from the transmission i think i need a slave cylinder.
- Asked by joe1953 about 9 months ago - 3 Answers
- 1989 Ford Ranger Drivetrain Problem
- My slave cylinder is leaking,when i fill the clutch master cylinder with fluid i can see it running out at the transmission.
- Asked by joe1953 about 9 months ago - 1 Answer
- 2002 Ford Ranger Drivetrain Problem with 186000 miles
- There is no power to the transfer case, motor or dash switch. All fuses have been replaced( although they were never bad. Also put a new ...
- Asked by Nathan.welker about 9 months ago - 1 Answer
- 1983 Ford Ranger Electrical Problem
- I was replacing the battery in my 1983 Ford Ranger truck and accidentally slipped and touched the metal body of the vehicle with the wrench ...
- Asked by UnderTheRose about 10 months ago - 1 Answer
- 1983 Ford Ranger Electrical Problem with 150000 miles
- I am changing from the standard wipers to delay wipers. I have all of the ford parts, the switch, the delay box, and the wiring. The old ...
- Asked by jme6109 about 10 months ago - 1 Answer
- 2003 Ford Ranger Engine Problem with 102000 miles
- If I rev the engine while in park it starts missing at 3000 rpm's out on the road it runs great
- Asked by 307 mo about 10 months ago - 5 Answers
- 1997 Ford Ranger problem
- Changed the starter, still won't start.
- Asked by dcmeza about 10 months ago - 3 Answers
- 1990 Ford Ranger Engine Problem with 100 miles
- I have a 1990 ford ranger. When i turn the key on the fuel pump runs continuously. Theres no power when i accelerate quickly and even ...
- Asked by dak about 10 months ago - 1 Answer
- 1994 Ford Ranger Electrical Problem
- To the Ford expert I wrote a question about spark plug for a 1994 Ford ranger that has a 4.0 motor the original plugs is awsf42pp I bought ...
- Asked by jrh1986 about 10 months ago - 1 Answer