2005 Mazda 6

Tiny
DARRELL47
  • MEMBER
  • 2005 MAZDA 6
Have no spark at spark plugs on a 2005 Mazda 6 I replaced the ignition coil pack but still no spark.
Do you
have the same problem?
Yes
No
Friday, December 17th, 2010 AT 2:00 AM

8 Replies

Tiny
KEN L
  • MASTER CERTIFIED MECHANIC
  • 42,544 POSTS
Hey DARRELL47,

Let start with a scan but it sounds like the crankshaft angle sensor has failed does it have fuel pressure?

Here are a few guides that will help you get the problem fixed.

https://www.2carpros.com/articles/car-cranks-but-wont-start

and

https://www.2carpros.com/articles/crankshaft-angle-sensor-replacement

and

https://www.2carpros.com/articles/checking-a-service-engine-soon-or-check-engine-light-on-or-flashing

Run some tests and get back to us so we can continue helping you.

Best, Ken
Was this
answer
helpful?
Yes
No
-1
Monday, January 30th, 2017 AT 1:57 AM
Tiny
ELLENRICKY
  • MEMBER
  • 2 POSTS
  • 2006 MAZDA 6
  • 2.3L
  • 4 CYL
  • 2WD
  • AUTOMATIC
  • 123,225 MILES
I have no spark at cylinder one ( it has individual coils for each cylinder ) so to trouble shoot the coil I plugged it into another coil plug that had spark and the coil worked. So I plugged it back into the number one cylinder and still no spark. So I checked power to the number one plug that plugs into coil and found power in one of the three wires but still no spark. All other coils get spark. Except for number one coil. No codes show up.?
Was this
answer
helpful?
Yes
No
Monday, January 30th, 2017 AT 1:59 AM (Merged)
Tiny
HMAC300
  • MECHANIC
  • 48,606 POSTS
Check fuel pressure and check compression and basic engine stuff like plugs wires etc. Then see if there is a vacuum leak like a line off etc. Spray choke cleaner around intake and throttle body.
Was this
answer
helpful?
Yes
No
-1
Monday, January 30th, 2017 AT 1:59 AM (Merged)
Tiny
ELLENRICKY
  • MEMBER
  • 2 POSTS
Did all that. All wire plugs that plug into coil pack have power. Each spark plug has its own coil pack. But no matter which coil pack I plug into the no one cylinder wire harness has no spark. But if I plug that same coil pack into the other individual wire harness for the other cylinders it gets spark but I have power at all the plugs that clip in to the coil packs could it be a crank to cam timing issue
Was this
answer
helpful?
Yes
No
+2
Monday, January 30th, 2017 AT 1:59 AM (Merged)
Tiny
HMAC300
  • MECHANIC
  • 48,606 POSTS
I don't think so, check your wiring as all the coils ae powered by the same wires and grounded the same except for two. Diagram at bottom of coil wiring. Might be a capacitor problem as well. Turbo motor in second pic
Was this
answer
helpful?
Yes
No
Monday, January 30th, 2017 AT 1:59 AM (Merged)
Tiny
HMAC300
  • MECHANIC
  • 48,606 POSTS
Forgot check connections as well as it can be a connection problem.
Was this
answer
helpful?
Yes
No
Monday, January 30th, 2017 AT 1:59 AM (Merged)
Tiny
CHANDY
  • MEMBER
  • 1 POST
  • 2003 MAZDA 6
  • 86,000 MILES
Check engine light on occassionally. Car stalled while driving. Cranks but wont start. Feul is pumping good. No sparks while cranking
Was this
answer
helpful?
Yes
No
+6
Monday, January 30th, 2017 AT 1:59 AM (Merged)
Tiny
HMAC300
  • MECHANIC
  • 48,606 POSTS
Get engine scanned auto parts do this for free
Was this
answer
helpful?
Yes
No
-1
Monday, January 30th, 2017 AT 1:59 AM (Merged)

Please login or register to post a reply.

Sponsored links