Taillight issue

Tiny
NIECYPOO
  • MEMBER
  • 2004 CADILLAC SRX
  • 6 CYL
  • 180,904 MILES
My right lamp is out but my brake light still works. When I drive I only have one tail light working (left side). When I put my right signal on it works but it flashes fast I do not know if I need a whole lamp or is there a replacement lights. I do not want the police tripping on me with one tail lamp on. Please I need answer on what to do.
Saturday, September 5th, 2015 AT 7:36 PM

11 Replies

Tiny
KEN L
  • MASTER CERTIFIED MECHANIC
  • 42,833 POSTS
Hello,

I would check the light bulb first but then hit up the fuse becasue if one fuse is out it will cause this problem.

Here are some guides that will help you get the problem fixed:

https://www.2carpros.com/articles/how-to-check-a-car-fuse

and

https://www.2carpros.com/articles/brake-lights-not-working

Here are the brake light diagrams and a guide to help you do some testing:

https://www.2carpros.com/articles/how-to-use-a-test-light-circuit-tester

Check out the diagrams (below).

Please let us know what you find. We are interested to see what it is.

Cheers, Ken
Was this
answer
helpful?
Yes
No
-1
Friday, December 8th, 2017 AT 7:53 PM
Tiny
ORV
  • MEMBER
  • 1 POST
  • 2006 CADILLAC SRX
How to remove rear tail lights?
Was this
answer
helpful?
Yes
No
Friday, December 8th, 2017 AT 7:54 PM (Merged)
Tiny
KEN L
  • MASTER CERTIFIED MECHANIC
  • 42,833 POSTS
Hi, the bolts to remove the lens are behind the trim panel. Below is a diagram to help you.

Please let us know what you find so it will help others.

Best, Ken
Was this
answer
helpful?
Yes
No
Friday, December 8th, 2017 AT 7:54 PM (Merged)
Tiny
LRAFTO
  • MEMBER
  • 1 POST
  • 2006 CADILLAC SRX
  • 50,000 MILES
Need to remove tail light housing to check for water leak into tire jack well on right side. I already replace the tail gate weather seal.
Was this
answer
helpful?
Yes
No
+1
Friday, December 8th, 2017 AT 7:54 PM (Merged)
Tiny
HMAC300
  • MECHANIC
  • 48,601 POSTS
There should be a couple of screws you can see once you open the lift-gate. If you have a water leak you should have the spare out and lift-gate closed then have a helper spray the back end of vehicle and on top to see if you can see the water coming in.
Was this
answer
helpful?
Yes
No
Friday, December 8th, 2017 AT 7:54 PM (Merged)
Tiny
RCARRIGER
  • MEMBER
  • 1 POST
  • 2004 CADILLAC SRX
  • 46,000 MILES
How do you replace tail light bulbs on vehicle listed above SUV? Both brake light and turn signal. I have found answers for sedans but not SUV. Are these led lights and is there a video? Thanks
Was this
answer
helpful?
Yes
No
Thursday, August 2nd, 2018 AT 3:17 PM (Merged)
Tiny
BLUELIGHTNIN6
  • MECHANIC
  • 16,542 POSTS
You need to open the rear tail gate and loosen the trim/carpeting first to gain access to the light assembly bolts. There should be plastic fasteners holding the trim on. Once removed you can see the bolts holding the assembly on. Remove these bolts and pull the tail light assembly out far enough to reach the bulbs.

Here is a guide that can help with a diagram below:

https://www.2carpros.com/articles/turn-signal-bulb-replacement

Check out the diagrams (below). Please let us know if you need anything else to get the problem fixed.

Cheers
Was this
answer
helpful?
Yes
No
+1
Thursday, August 2nd, 2018 AT 3:17 PM (Merged)
Tiny
VWOLFE
  • MEMBER
  • 2 POSTS
  • 2005 CADILLAC SRX
  • 65,000 MILES
How to change running light bulb?
Was this
answer
helpful?
Yes
No
+2
Thursday, August 2nd, 2018 AT 3:17 PM (Merged)
Tiny
JACOBANDNICKOLAS
  • MECHANIC
  • 108,128 POSTS
Are you referring to the parking lights?
Was this
answer
helpful?
Yes
No
Thursday, August 2nd, 2018 AT 3:17 PM (Merged)
Tiny
VWOLFE
  • MEMBER
  • 2 POSTS
The front running lights that are also the turn signal lights in the front. Amber colored. Most GM have white lights like headlamps as running lights, but not for
Cadillac. I cannot seem to find a way to get to the headlight assembly without having
to take off the whole front grille or bumper. Baffling! A simple lamp to replace
but how to get to it?
Was this
answer
helpful?
Yes
No
-1
Thursday, August 2nd, 2018 AT 3:17 PM (Merged)
Tiny
JACOBANDNICKOLAS
  • MECHANIC
  • 108,128 POSTS
If you open the hood, check along the rad support for vertical pins that hold the assembly in place. Some used these. If they are there, pull up on them and the assembly will come out.
Was this
answer
helpful?
Yes
No
Thursday, August 2nd, 2018 AT 3:17 PM (Merged)

Please login or register to post a reply.

Sponsored links