Possible blown head gasket

Tiny
ADF020
  • MEMBER
  • 2018 FORD MUSTANG
  • 2.3L
  • 4 CYL
  • TURBO
  • 2WD
  • AUTOMATIC
  • 8,900 MILES
I have recently been seeing white smoke come out of my exhaust when I start my car in the morning. It is garage-kept. The car has been well maintained. I have a tune on it as well as an aftermarket cold air intake.

Due to the smoke, I purchased one of those chemical head gasket leak testers where the fluid will turn from blue to yellow if you have exhaust gasses in the coolant reservoir. My result is in the image below. It isn't yellow, but it isn't blue either.

I was going to buy a gas analyzer to test for hydrocarbons, but they are $1,000.00+. What is my best bet here? Do you think I have a head gasket leak with a car so new?

I doubt Ford would warranty it due to the tune on it.

If you think I need a replacement gasket, can you link to how to preform the DIY for the 2018 mustang ecoboost? Can't find any videos on it.
Do you
have the same problem?
Yes
No
Tuesday, January 29th, 2019 AT 9:23 PM

20 Replies

Tiny
DANNY L
  • MECHANIC
  • 5,648 POSTS
Hello, I'm Danny.

Just a question first. Have you been noticing a loss of coolant? Do you have to keep adding to the overflow or radiator? Here is a tutorial about white smoke:

That looks like a positive test, but I also noticed the fluid is above the fill line. Any coolant in the test will contaminate it

Does it run rough at all when cold started?

Any overheating?

Does it blow coolant into the overflow when warmed up?

Do you notice excessive cooling system pressure when its fully warmed up? (Upper hose swelling)

https://www.2carpros.com/articles/white-smoke-or-steam-coming-from-the-exhaust-pipe

Hope this helps and thanks for using 2CarPros.
Danny-
Was this
answer
helpful?
Yes
No
Tuesday, January 29th, 2019 AT 9:33 PM
Tiny
ADF020
  • MEMBER
  • 9 POSTS
No loss of coolant is noticed. Just the white smoke and the chemical test. I did check the coolant reservoir and it had some sandy stuff in it. I read that could be due to poor flushing process from manufacturing? I think that is unrelated.
Was this
answer
helpful?
Yes
No
Tuesday, January 29th, 2019 AT 10:00 PM
Tiny
ADF020
  • MEMBER
  • 9 POSTS
But, what is your advice? Do you think it is a blown gasket? Do you have any guide to replace a head gasket myself for this car or can you ping someone who knows onto this thread?
Was this
answer
helpful?
Yes
No
Tuesday, January 29th, 2019 AT 10:09 PM
Tiny
KASEKENNY
  • MECHANIC
  • 18,907 POSTS
Just to jump in. I have seen this a number of times when the fluid does not change from blue to yellow but green instead. However, if you go back to 1st grade, blue and yellow make green so this means you have a small leak in the head gasket that is only allowing a small amount of hydrocarbons into the coolant.

Here is a guide that talks about this:

https://www.2carpros.com/articles/head-gasket-blown-test

Also, here is a guide that talks about the white smoke:

https://www.2carpros.com/articles/white-smoke-or-steam-coming-from-the-exhaust-pipe

Clearly Danny already provided the instructions on the head gasket but these guides will help others confirm a head gasket if they visit the site. Thanks
Was this
answer
helpful?
Yes
No
Tuesday, December 1st, 2020 AT 12:39 PM
Tiny
ASEMASTER6371
  • MECHANIC
  • 52,797 POSTS
Good evening,

I attached the procedure and pictures for you of the process for replacing the head gasket.

I would have a leak down test done to confirm to be sure it is the issue.

Roy

303-01A Engine - 2.3L EcoBoost (231kW/314PS) 2018 Mustang
Removal and Installation
Cylinder Head
Base Part Number: 6051
Special Tool(s) / General Equipment

Oil Drain Equipment
Hose Clamp Remover/Installer
Removal

NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure. The crankshaft pulley and the crankshaft timing sprocket are not keyed to the crankshaft. The crankshaft, the crankshaft sprocket and the pulley are fitted together by friction. For that reason, the crankshaft sprocket is also unfastened if the pulley bolt is loosened. Before any repair requiring loosening or removal of the crankshaft pulley bolt, the crankshaft and camshafts must be locked in place by the special service tools, otherwise severe engine damage can occur.

NOTICE: During engine repair procedures, cleanliness is extremely important. All parts must be thoroughly cleaned and any foreign material, including any material created while cleaning gasket surfaces, that enters the oil passages, coolant passages or the oil pan, can cause engine failure.

With the vehicle in NEUTRAL, position it on a hoist.
Refer to: Jacking and Lifting - Overview (100-02 Jacking and Lifting, Description and Operation).
Remove the nuts and the engine appearance cover.
Image
Release the fuel system pressure.
Refer to: Fuel System Pressure Release (310-00A Fuel System - General Information - 2.3L EcoBoost (231kW/314PS), General Procedures).
Disconnect the battery ground.
Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
Drain the cooling system.
Refer to: Cooling System Draining, Vacuum Filling and Bleeding (303-03A Engine Cooling - 2.3L EcoBoost (231kW/314PS), General Procedures).
Remove the following items:
Remove the turbocharger.
Refer to: Turbocharger (303-04D Fuel Charging and Controls - Turbocharger - 2.3L EcoBoost (231kW/314PS), Removal and Installation).
Remove the intake manifold.
Refer to: Intake Manifold (303-01A Engine - 2.3L EcoBoost (231kW/314PS), Removal and Installation).
Remove the camshafts.
Refer to: Camshafts (303-01A Engine - 2.3L EcoBoost (231kW/314PS), Removal and Installation).
NOTE: If the valve tappets are to be reused, note the location of the valve tappets to make sure they are assembled in their original positions.

Remove the valve tappets.
ImageOpen In New TabZoom/Print

Detach and disconnect the fuel rail electrical connector.
Detach the wiring harness retainers.
Remove the fuel rail insulator shield.
Image

Disconnect and position the coolant tube aside.
Use the General Equipment: Hose Clamp Remover/Installer
imageOpen In New TabZoom/Print

Disconnect the fuel injector and the FRP sensor electrical connectors.
Image

Disconnect the ECT sensor electrical connector from the back of the engine.
ImageOpen In New TabZoom/Print

Disconnect the crankcase vent tube sensor electrical connector and wire harness retainer.
Detach the crankcase vent tube retainer and remove.
Image

Disconnect the upper radiator hose from the coolant outlet tube.
Use the General Equipment: Hose Clamp Remover/Installer
Disconnect the coolant by-pass hose from the degas bottle.
Use the General Equipment: Hose Clamp Remover/Installer
imageOpen In New TabZoom/Print

Remove the bolt from the cylinder head and remove the coolant tube from coolant outlet.
Image

Remove and discard the coolant tube O-ring seal.
ImageOpen In New TabZoom/Print

Slide the insulator up and disconnect the CHT sensor electrical connector.
Image

Remove the bolts and the coolant tube.
ImageOpen In New TabZoom/Print

Inspect the coolant tube O-ring seal and replace if necessary.
Image

Remove the bolt and the ground wire.
ImageOpen In New TabZoom/Print

Disconnect the heater hose from the coolant outlet.
Use the General Equipment: Hose Clamp Remover/Installer
image

Remove the bolts and the cylinder head.
Discard the bolts.
ImageOpen In New TabZoom/Print

Remove and discard the cylinder head gasket.
Image

NOTICE: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges that make leak paths. Use a plastic scraping tool to remove all traces of the head gasket.

NOTE: Clean the cylinder head bolt holes in the cylinder block. Make sure all coolant, oil or other foreign material is removed.

Make sure that the mating faces are clean and free of foreign material.
ImageOpen In New TabZoom/Print

Check the cylinder head distortion.
Refer to: Cylinder Head Distortion (303-00 Engine System - General Information, General Procedures).
Check the cylinder block distortion.
Refer to: Cylinder Block Distortion (303-00 Engine System - General Information, General Procedures).
Installation

Install the cylinder head gasket.
Image

NOTE: The cylinder head bolts are torque-to-yield and must not be reused. New cylinder head bolts must be installed.

Install the cylinder head and the new bolts.
Torque :
Stage 1: 62 lb. In (7 Nm)
Stage 2: 133 lb. In (15 Nm)
Stage 3: 41 lb. Ft (55 Nm)
Stage 4: 90°
Stage 5: 90°
Was this
answer
helpful?
Yes
No
Tuesday, December 1st, 2020 AT 2:20 PM
Tiny
RANDALL ROJAS
  • MEMBER
  • 1 POST
  • 2007 FORD MUSTANG
  • 4.6L
  • V8
  • 2WD
  • MANUAL
  • 148,000 MILES
Hello, with a small head gasket leak, had anyone tried blue devil, bars stop leak, bars head gasket fix, or Steel seal?
Was this
answer
helpful?
Yes
No
Wednesday, December 2nd, 2020 AT 9:01 AM (Merged)
Tiny
ASEMASTER6371
  • MECHANIC
  • 52,797 POSTS
Good morning.

I never recommend any add in sealant as they rarely work. The only correct repair is to replace the head gasket.

The sealants clog the radiator and the heater core and do nothing but create more issues.

I hear many people the blue devil works but if it does, and I doubt it, it will be very temporary.

Roy
Was this
answer
helpful?
Yes
No
Wednesday, December 2nd, 2020 AT 9:01 AM (Merged)
Tiny
2CP-ARCHIVES
  • MEMBER
  • 4,544 POSTS
  • 2005 FORD MUSTANG
  • 30,000 MILES
Hi I am looking at buying a 2005 mustang gt and the owner says he changed the head gaskets on the car cause these engines are known to sweat a lot should I be worried? If he blew the head gasket is the car toast? Anyways give me your opinion thanks
Was this
answer
helpful?
Yes
No
Wednesday, December 2nd, 2020 AT 9:01 AM (Merged)
Tiny
HMAC300
  • MECHANIC
  • 48,606 POSTS
If it doesn'tuse oil and the coolant level is full it may be ok, have it pressure tested for an internal leak if it was done right it should last for quite a while.
Was this
answer
helpful?
Yes
No
Wednesday, December 2nd, 2020 AT 9:01 AM (Merged)
Tiny
DAISYGRUMBLER
  • MEMBER
  • 4 POSTS
  • 2002 FORD MUSTANG
  • V6
  • 2WD
  • AUTOMATIC
I am thinking about buying my brothers 2002 ford mustang. He was overheating so he took it to a shop and they changed the radiator now it only over heats when the air conditioner is on. The shop said they were not sure but the head gasket might be starting to go bad but they did not do a compression test. I dont want to buy it if the head may go bad, how can a shop say it may be starting to go bad but it may be just fine? It has plenty of power, oil is good has no water in oil or anything like that it does not smoke or anything. How can you actually tell if the head is going to go bad or not? Also I heard of something called blue devil that prevents the head from going bad. Have you ever used blue devil or heard anything good or bad about it?
Was this
answer
helpful?
Yes
No
Wednesday, December 2nd, 2020 AT 9:02 AM (Merged)
Tiny
HMAC300
  • MECHANIC
  • 48,606 POSTS
Have the cooling system pressure checked to see if the head/intake gasket is bad. Also check to see if your cooling fans come on when the a/c is on they should. Check the items in pic then have it scanned to see if fan module is ok.
Was this
answer
helpful?
Yes
No
Wednesday, December 2nd, 2020 AT 9:02 AM (Merged)
Tiny
AWDEVORE
  • MEMBER
  • 2 POSTS
  • 2001 FORD MUSTANG
I was told I probably have a blown head gasket as my car started smoking and there is a leak in the radiator. It probably ran hot for a few moments although I was watching closely. Anyway, my question is how difficult is this job if I get an excellent manual. I can put computers and furnature together, but only have changed an oil and my thermstat on my car. I can follow instructions, but I want to know your opinion?
Was this
answer
helpful?
Yes
No
Wednesday, December 2nd, 2020 AT 9:02 AM (Merged)
Tiny
TAURUSWHEEL
  • MECHANIC
  • 718 POSTS
Find a reputable repair shop, the Ford Dealer maybe, and get a leakdown test performed to confirm a blown headgasket. Specify you want a leakdown test. Don't tear it apart until you have a confirmed diagnosis of whatever the issue is. If the headgasket is indeed bad, the heads should be checked for warpage also while it's apart. Did you overheat the engine? Worst thing you can do to an engine short of no oil. A smoking engine and a leaky rad are two seperate issues, what color was the smoke? Oil= blue, coolant= white, gas= black. If you think you're burning coolant stick your nose down by the tailpipe, take yourself a nice whiff, you may be able to catch a whiff of antifreeze in the exhaust, you'll know the smell, not scientific by any means though
Was this
answer
helpful?
Yes
No
Wednesday, December 2nd, 2020 AT 9:02 AM (Merged)
Tiny
SPOOKYCC
  • MEMBER
  • 1 POST
  • 2001 FORD MUSTANG
  • 3.8L
  • 6 CYL
  • RWD
  • MANUAL
  • 160,000 MILES
Oil droplets small amount in reservoir. Mechanic does not want me to spend money on tracking down internal leak. New head gasket and cylinders machined two years ago. No head gasket symptoms. Runs fine, does not overheat.

I want to use Bars coolant system fix. It says to put in radiator if possible. If my radiator is full should I drain some and then add the coolant fix product? Or put it in the overflow reservoir? I never use leak stops as a rule but we are just trying to get as many miles as we can before I replace the car.

Thanks so much!

Colleen
Was this
answer
helpful?
Yes
No
Wednesday, December 2nd, 2020 AT 9:02 AM (Merged)
Tiny
HARRY P
  • MECHANIC
  • 2,293 POSTS
As a general rule I stay away from putting stop leak in a cooling system. As its job is to plug up little holes, what it often ends up doing is plugging up the little passages through the radiator, making it easier for your car to overheat, and still leak anyways. If you are going to use it though, I would suggest letting a little coolant out by either opening the drain cock on the bottom of the radiator tank (passenger side) or by taking off the lower hose for a few seconds and then putting it back on, then put the stuff in. I know several people who swear by Blue Devil Head Gasket Sealant. https://www.amazon.com/BlueDevil-Head-Gasket-Sealer-ounce/dp/B000NOO798.
I kind of doubt that it actually works, but could be worth a shot.
Was this
answer
helpful?
Yes
No
Wednesday, December 2nd, 2020 AT 9:02 AM (Merged)
Tiny
STEVE W.
  • MECHANIC
  • 12,883 POSTS
Blue Devil works but only for true head gasket leaks. In this case oil getting into the coolant I would not use it. Why? Because it is the same chemical that was used during the cash for clunkers fiasco. Water glass aka sodium silicate, If it gets into the oiling system it will destroy the engine in a very, very short time and it will not be repairable.

I would suspect that it is a front cover leak and not top end as there are no pressurized oil passages through the head gaskets, just drain back ports.
Unless this is a supercharged engine, those have an engine oil cooler in the radiator that could leak.
Was this
answer
helpful?
Yes
No
Wednesday, December 2nd, 2020 AT 9:02 AM (Merged)
Tiny
HARRY P
  • MECHANIC
  • 2,293 POSTS
Hmmm, I guess it is true that you learn something new every day. Thanks for that Steve!
Was this
answer
helpful?
Yes
No
Wednesday, December 2nd, 2020 AT 9:02 AM (Merged)
Tiny
OSCR72
  • MEMBER
  • 1 POST
  • 2000 FORD MUSTANG
  • V8
  • 2WD
  • MANUAL
  • 190,000 MILES
How much work is involved in changing the head gasket and what would the parts normally cost? Is this a project that anybody can do themselves or is this a job for a mechanic?
Was this
answer
helpful?
Yes
No
Wednesday, December 2nd, 2020 AT 9:03 AM (Merged)
Tiny
BLACKOP555
  • MECHANIC
  • 10,371 POSTS
If you have the tools your self. Some patients. A decent set of tools then you should be able to do it yourself no problem. It shouldnt cost more then 200 bucks parts.
Was this
answer
helpful?
Yes
No
+1
Wednesday, December 2nd, 2020 AT 9:03 AM (Merged)
Tiny
FORDRACING24
  • MEMBER
  • 65 POSTS
A couple hundred bucks for the head gaskets and a torque wrench with a basic set of tools and you should be just fine.
Was this
answer
helpful?
Yes
No
+1
Wednesday, December 2nd, 2020 AT 9:03 AM (Merged)

Please login or register to post a reply.

Sponsored links