SPONSORED LINKS

Why does the Left turn signal and hazard light not work at all?

Tiny
IOWAN86
  • MEMBER
  • 2002 SATURN SC2
  • 233,333 MILES
The Left turn signal and hazard light does not work at all, the green flashing light on the inside does not even start blinking. But the Right side works no problems what so ever. What could cause this? Thank you.
Tuesday, August 28th, 2012 AT 8:36 PM

20 Replies

Tiny
CJ MEDEVAC
  • MECHANIC
  • 11,004 POSTS
HAVE YOU TRIED A NEW BULB. THE CORRECT BULB?

SOMETIMES SNATCHING A BULB IN AND OUT OF THE SOCKET A FEW TIMES WILL GIVE A BETTER CONNECTION

saturntech9 IS GONNA GET ME FOR ANSWERING HERE!

I DON'T KNOW HOW YOUR BULBS ARE HELD IN. IF IT HAS A REMOVABLE HOLDER (WHICH HAS NO WIRES ATTACHED) THAT YOU PUT THE BULB INTO IT THEN TWIST INTO THE HOUSING. THE HOLDER MAY HAVE CONNECTIONS WHICH MATE TO CONTACTS IN THE HOUSING

IF YOURS IS LIKE THIS---CLEAN THE CONNECTIONS ON BOTH THE HOLDER AND THE HOUSING

IF IT'S NOT LIKE THIS, YOU MAY HAVE A GROUND OR OTHER PROBLEM

I'M SURE saturntech9 IS GONNA JUMP IN AND TAKE OVER. TELL US WHAT YOU HAVE THUS FAR. FIND YOU AN INEXPENSIVE DIGITAL VOLTMETER (VERIFY YOU ARE READY)

IF HE DON'T SHOW.I'LL GO GET HIM!

THE MEDIC
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
Tuesday, August 28th, 2012 AT 9:25 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,870 POSTS
Iam here and iam everywhere lol. If its not lighting up on the cluster or the bulbs its not a loose bulb connection.A bad bulb or connection would just make thay side flash faster. You will need a multimeter but perferably a test light that reads power and ground. Most likely were looking at a flasher relay.
Was this
answer
helpful?
Yes
No
-1
Tuesday, August 28th, 2012 AT 10:05 PM
Tiny
IOWAN86
  • MEMBER
  • 43 POSTS
Wouldn't the flasher relay work for both sides or is there two different relays, one for each side? If there are two different ones can I just flip flop them to see if this is the problem? I have a test light but only reads power, has to be grounded.
Was this
answer
helpful?
Yes
No
-1
Tuesday, August 28th, 2012 AT 10:36 PM
Tiny
CADIEMAN
  • MECHANIC
  • 3,544 POSTS
Remove the bulb and ck for burnt filements. Their should be 2 1 for parking lights and 1 for signal lights. For the price of a bulb just replace it. Gl
Was this
answer
helpful?
Yes
No
-1
Wednesday, August 29th, 2012 AT 12:31 AM
Tiny
IOWAN86
  • MEMBER
  • 43 POSTS
As stated above the LEFT interior flasher on the cluster does not even blink on and off or even go on at all. I will just wait till I get another response from Saturntech9. Thank you
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
Wednesday, August 29th, 2012 AT 3:12 AM
Tiny
CJ MEDEVAC
  • MECHANIC
  • 11,004 POSTS
THAT IS THE "ALERT" FROM THE COCKPIT THAT SOMETHING MAY BE WRONG WITH THE EXTERNAL LAMPS IN THE LEFT SIDE CIRCUIT. COULD BE FRONT/ REAR/ EVEN SIDE MARKERS

NOT MUCH COMING THRU RIGHT NOW. WE ALL GET BORED AND WANNA HELP SOMEBODY. Saturntech9 WILL BE BACK SOON (WHEREVER HE WENT) I UNDERSTAND."HE'S THE MAN".I LOVE 'IM TOO! LOL!

THE MEDIC
Was this
answer
helpful?
Yes
No
+1
Wednesday, August 29th, 2012 AT 3:32 AM
Tiny
CADIEMAN
  • MECHANIC
  • 3,544 POSTS
The light wont blink because 1 of bulbs is bad.I dont know where saturn went
Was this
answer
helpful?
Yes
No
Wednesday, August 29th, 2012 AT 7:10 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,870 POSTS
If a bulb is burned out the indicator on the cluster will still blink just blinks faster. Just to get this straight no turn signal indicator lit up or flashing on the cluster or the front and rear outside turn signal bulbs on the left side?
Was this
answer
helpful?
Yes
No
Wednesday, August 29th, 2012 AT 8:27 PM
Tiny
IOWAN86
  • MEMBER
  • 43 POSTS
Correct. The left turn signals wont work at all even when the hazard is set. But the right side all works perfectly fine.
Was this
answer
helpful?
Yes
No
Wednesday, August 29th, 2012 AT 9:11 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,870 POSTS
Turn on the hazzards you should have power at the yellow wire at the combo switch?
Was this
answer
helpful?
Yes
No
-1
Thursday, August 30th, 2012 AT 2:38 AM
Tiny
IOWAN86
  • MEMBER
  • 43 POSTS
When you say combo switch do you mean the plug at the bottom of the steering column? Or the plug that plugs into the turn signal switch. I turned the hazards on and the yellow wire at the bottomside of the steering wheel had no power to it.
Was this
answer
helpful?
Yes
No
Friday, August 31st, 2012 AT 10:23 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,870 POSTS
The yellow wire coming right out of the turn signal switch behind the steering wheel.
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
Friday, August 31st, 2012 AT 10:46 PM
Tiny
IOWAN86
  • MEMBER
  • 43 POSTS
Out of the turn signal switch there is no yellow wire, there is an orange, brown, black, blue and two pink ones.
Was this
answer
helpful?
Yes
No
Friday, August 31st, 2012 AT 11:07 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,870 POSTS
The light blue wire is the power feed from the hazzard switch into the Lever combination switch. The yellow wire feeds the power to the left bulbs and the Dark green wire feeds the right side bulbs.I posted part of the diagram for you to see what iam talking about.
Image (Click to make bigger)
Thumb
Was this
answer
helpful?
Yes
No
Saturday, September 1st, 2012 AT 4:35 AM
Tiny
IOWAN86
  • MEMBER
  • 43 POSTS
Then the only yellow wire back there has no power to it when the hazards are flashing.
Was this
answer
helpful?
Yes
No
Sunday, September 2nd, 2012 AT 12:57 AM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,870 POSTS
Next thing I would do is unplug the connector that has the yellow wire and see if the terminal end is bent open compare it to the other terminals in the connector.
Was this
answer
helpful?
Yes
No
Sunday, September 2nd, 2012 AT 9:30 PM
Tiny
IOWAN86
  • MEMBER
  • 43 POSTS
There is no way to unplug it without taking the switch off. There is no room to pull the plug out any. So dont think it would be that. Checked the green wire when hazards on and it was flashing my test light perfect.
Was this
answer
helpful?
Yes
No
Sunday, September 2nd, 2012 AT 11:17 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,870 POSTS
I have seen terminals that were open and the connectors were never unplugged on those cars. Your down to the switch or the terminal accorrding to the wire diagram.
Was this
answer
helpful?
Yes
No
Sunday, September 2nd, 2012 AT 11:22 PM
Tiny
IOWAN86
  • MEMBER
  • 43 POSTS
So couldn't be a flasher relay then? Guess I will have to pull the switch off and check the terminal. This might take me a day or two to get time to do this.
Was this
answer
helpful?
Yes
No
Sunday, September 2nd, 2012 AT 11:34 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,870 POSTS
For the hazzard function the power come from the hazzard fuse thru the hazzard switch thru the combo switch then out the yellow wire and the dark green wire. If there is power at the dark green wire then you know there is power to the switch and atleast coming out of one side of the switch. So its ethier the switch or more likely a open bad terminal tightness issue.
Was this
answer
helpful?
Yes
No
Sunday, September 2nd, 2012 AT 11:53 PM

Please login or register to post a reply.

Related Hazard Light Not Working Content

Sponsored links