2001 Oldsmobile Alero

Tiny
BLUFFHUNTER
  • MEMBER
  • 2001 OLDSMOBILE ALERO
  • 6 CYL
  • FWD
  • AUTOMATIC
  • 140,000 MILES
2001 Oldsmobile Alero 3.4. NO HEAT
changed the thermostat, Flushed heater core, new heater hose. Still blowing warm, not hot. Seems like it's not circulating properly. If it was the water pump wouldn't it have a overheating problem? Engine temp is normal. Does this car have a heater control valve and could it be the problem? Radiator hoses seem fine also, but when up to temperature, one radiator hose is hot, but the other is just warm. I don't know what to check out next. Any suggestions would be greatly appreciated. Thank you in advance !
Do you
have the same problem?
Yes
No
Monday, November 29th, 2010 AT 2:57 PM

13 Replies

Tiny
WRENCHTECH
  • MECHANIC
  • 20,758 POSTS
With the engine at full operating temp, locate the 2 heater hoses where they go into the firewall and feel them to see if they are both too hot to hold. If they are.

The heat in that vehicle is controlled by a blend door that regulates heated air flow. It is operated by an electric motor/actuator. The problem can be that the actuator is stripped or inoperative or the door itself could be damaged. This is what needs to be determined by examining the actuator and see if it is responding to heat change commands or not.
Was this
answer
helpful?
Yes
No
Monday, November 29th, 2010 AT 3:04 PM
Tiny
BLUFFHUNTER
  • MEMBER
  • 14 POSTS
Hi Wrenchtech,
The heater hoses were not to hot to hold, which I thought was odd. I had wondered if there might be some sort of electrical part that might be not letting it circulate properly. I will research a little more when I have the car again. Thanks for the info on the actuator. I am sure it won't have easy access to check it out.
Was this
answer
helpful?
Yes
No
-1
Monday, November 29th, 2010 AT 3:43 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,758 POSTS
If the hoses are not both hot, then you have a restriction in the heater core.
Was this
answer
helpful?
Yes
No
+1
Monday, November 29th, 2010 AT 4:05 PM
Tiny
BLUFFHUNTER
  • MEMBER
  • 14 POSTS
Thanks wrenchtech. Unless it's a new restriction ( which it had a restriction when I started all of this )I flushed the heater core out backwards then the normal direction and before I reconnected the hoses to the engine and I had normal flow through the heater core at that point. I guess it's possible that something else might have came through the system to restrict it again. No type of stop leak or anything has been used in this cooling system that I am aware of. Thanks again
Was this
answer
helpful?
Yes
No
Monday, November 29th, 2010 AT 4:21 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,758 POSTS
That doesn't mean the core has good flow. It can be 75% restricted and still act that way.
Was this
answer
helpful?
Yes
No
Monday, November 29th, 2010 AT 4:23 PM
Tiny
BLUFFHUNTER
  • MEMBER
  • 14 POSTS
Oh, good point ! Might just be going in one fitting and right back out the other? I have never thought about that. I really hate the thought of pulling the core, but I might be looking at that in the near future. I did get some heat after flushing it compared to blowing cold air before I started all of this.
Thanks again for the responce. I guess I know what I will be doing this weekend if not before :( I just hate messing with taking the dash apart unless it's absolutely nessessary !
Was this
answer
helpful?
Yes
No
Monday, November 29th, 2010 AT 4:49 PM
Tiny
BLUFFHUNTER
  • MEMBER
  • 14 POSTS
Would there be a chance I could just disconnect both heater core lines from the engine and dump some radiator flush into them and let it sit for a while, and expect it to clean up the core? Just a thought.
Was this
answer
helpful?
Yes
No
Monday, November 29th, 2010 AT 4:52 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,758 POSTS
That's what I would try. I had the same problem with my own Blazer and I eventually got it cleaned out after numerous flushing. It was caked with Dexcool sludge which is probably what yours has too. Flush the rest of the engine too because it may just plug right back up again.
Was this
answer
helpful?
Yes
No
Monday, November 29th, 2010 AT 5:00 PM
Tiny
BLUFFHUNTER
  • MEMBER
  • 14 POSTS
Thanks again !
I do know that they used dexcool until they heard that it was bad on head gaskets and a few other things, so you might be onto to something there. I will probably try flushing again when possible.
What anti-freeze is acceptable for a replacement of the dexcool, when the manufacturer recommends the dexcool? We have ran that in my wife's Grandam for quite a while?
Thanks Wrenchtech ! I will post what ends up fixing this problem to help others that encounter this.
Was this
answer
helpful?
Yes
No
Monday, November 29th, 2010 AT 5:32 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,758 POSTS
There is nothing wrong with Dexcool. The problem is the maintenance on the vehicle. Dexcool is 5 year maximum and it has to be changed and if the system has any leaks, the introduction of air into the system causes big problems. Your car is a 2001 so if that coolant is original, that explains your problem.
Was this
answer
helpful?
Yes
No
Monday, November 29th, 2010 AT 5:36 PM
Tiny
BLUFFHUNTER
  • MEMBER
  • 14 POSTS
I know they changed the antifreeze about a year ago, but may have been after the damage was done already. They have only owned this car a little over a year. It's starting to get to be a headache with all of the repairs it's needed in the past couple of months. The previous owners didn't keep it up to well, I think.
Was this
answer
helpful?
Yes
No
Monday, November 29th, 2010 AT 6:54 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,758 POSTS
You may have some leaks show up after flushing too. The sludge may be holding them back while it corrodes the metal.
Was this
answer
helpful?
Yes
No
Monday, November 29th, 2010 AT 6:58 PM
Tiny
BLUFFHUNTER
  • MEMBER
  • 14 POSTS
DON'T SAY THAT ! Oh well, I know that is a realization that might have to be dealt with. First come first served.
Was this
answer
helpful?
Yes
No
Monday, November 29th, 2010 AT 7:03 PM

Please login or register to post a reply.

Sponsored links