SPONSORED LINKS

Help

Tiny
KYLEKUEBER
  • MEMBER
  • 2006 SATURN ION
06 saturn ion 2. Replace the starter and ignition switch, but car still doesn't turn over and fuel pump isn't humming. What to do next? Also reset passlock, that should be fine
Monday, September 3rd, 2012 AT 7:21 PM

14 Replies

Tiny
ASEMASTER6371
  • MECHANIC
  • 52,797 POSTS
Start with basics.

Do you have power at the starter? Is the little wire hot in the start position?

Re set the passlock? How did you do this?

Roy
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
-2
Monday, September 3rd, 2012 AT 8:43 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,870 POSTS
Just to add to this one how did you relearn the pass lock?Also is the security light on solid or flashing?If it is then that's where we need to start by getting the pass lock learned. Or find out why the light is on.
Was this
answer
helpful?
Yes
No
+2
Monday, September 3rd, 2012 AT 10:06 PM
Tiny
KYLEKUEBER
  • MEMBER
  • 7 POSTS
I have power to the starter. With a little help we were able to jump the starter and it turned over nicely. As for the passlock: after I installed the new ignition switch it tried to start the car, then left it in the on position until the icon went out on the dash. I then shut it of for 30 sec, then repeated the procedure until the icon did not show up in the on position. That is where i'm at now, with still no power to the fuel pump. I also have coolant/ pwr steering flashing on the dash.
Was this
answer
helpful?
Yes
No
+2
Tuesday, September 4th, 2012 AT 11:06 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,870 POSTS
You said you have power to the starter by jumping the starter with a hot wire?Also is the security light on solid or flashing?Is the coolant low?
Was this
answer
helpful?
Yes
No
+1
Wednesday, September 5th, 2012 AT 1:30 AM
Tiny
KYLEKUEBER
  • MEMBER
  • 7 POSTS
The starter is good. The security light is no longer on when the ignition in is the "on" position. Coolant is good. When I turn the key all I hear is the ignition switch clicking, nothing else.
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
+2
Wednesday, September 5th, 2012 AT 8:13 AM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,870 POSTS
So when you turn the key to the start position there is no power to the purple wire at the starter?
Was this
answer
helpful?
Yes
No
+3
Wednesday, September 5th, 2012 AT 3:33 PM
Tiny
KYLEKUEBER
  • MEMBER
  • 7 POSTS
Right. No power to the starter or the fuel pump. Both of those fuses look good. This is my nieces car, recently spoke to her and what she claims is that the car completely shut down while she was driving.
Was this
answer
helpful?
Yes
No
Wednesday, September 5th, 2012 AT 10:56 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,870 POSTS
Have you checked for codes in the computer yet?Also just because you can't hear the fuel pump doesn't mean the pump. Isn't working.
Was this
answer
helpful?
Yes
No
+1
Wednesday, September 5th, 2012 AT 11:14 PM
Tiny
KYLEKUEBER
  • MEMBER
  • 7 POSTS
Found error code U0100 Lost Comm. With ECM/PCM Module A.
Was this
answer
helpful?
Yes
No
Thursday, September 6th, 2012 AT 11:27 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,870 POSTS
The next thing I would do you wont be able to do with a basic scan tool is see if you can read data and codes from the body control module. Does your gas gauge temp gauge keyless entry etc work?
Was this
answer
helpful?
Yes
No
+1
Thursday, September 6th, 2012 AT 11:30 PM
Tiny
KYLEKUEBER
  • MEMBER
  • 7 POSTS
Unsure about the gas gauge and temp gauge, but I know the keyless entry does work
Was this
answer
helpful?
Yes
No
Friday, September 7th, 2012 AT 12:57 AM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,870 POSTS
The temp gauge I can understand since its cold and hasnt run. But how do you not know if the the gas gauge works?Does it show any gas on the gauge when turning the key on?
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
Friday, September 7th, 2012 AT 1:02 AM
Tiny
KYLEKUEBER
  • MEMBER
  • 7 POSTS
Problem solved. Found that the fuse on the little positive wire going to the battery was blown. New fuse and car started. Thanks for your help.
Was this
answer
helpful?
Yes
No
Sunday, September 9th, 2012 AT 8:05 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,870 POSTS
Your welcome glad to hear you got it fixed I thought you said you checked the fuses. Atleast its fixed now.
Was this
answer
helpful?
Yes
No
Monday, September 10th, 2012 AT 2:11 AM

Please login or register to post a reply.

Related Ignition Switch Replace/Remove Content

VIEW MORE

Sponsored links