SPONSORED LINKS

What to do if debris in coolant reservoir after few weeks after flush

Tiny
ROYCAR71
  • MEMBER
  • 1998 GMC JIMMY
  • 6 CYL
  • AUTOMATIC
  • 125,708 MILES
Just did a coolant flush 2 weeks ago. I backflushed old coolant using my prestone tee hook up to my inlet hose. I used prestone flush solvent following instructions. Everything seemed ok for about 2 weeks. Now I see brown stuff in coolant reservoir that could be rust or some leak fix I used years ago when I have bad radiator and finally I had replaced about 3 years ago. What would be best course of action?
SPONSORED LINKS
Tuesday, June 26th, 2012 AT 9:33 AM

12 Replies

Tiny
WRENCHTECH
  • MECHANIC
  • 20,757 POSTS
Once you have sludge in a system, it's about impossible to get it all cleaned out. Have it professionally flushed because those tees really don't do much.
Was this
answer
helpful?
Yes
No
+1
Tuesday, June 26th, 2012 AT 10:09 AM
Tiny
KHLOW2008
  • MECHANIC
  • 41,815 POSTS
Single flush never works as some debris would be knocked loose and it is a matter of time before they surfaces. For badly sludged systems, it might take 3 or 4 flushes over a period before they become really clean. Of course you need to run the vehicle for some time in between flushing.

Note your coolant quality.

I would usually flush and run without any coolant for one or 2 days and reflush until the water becomes clean. RO water would be the best choice to use for this.
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
+1
Tuesday, June 26th, 2012 AT 2:23 PM
Tiny
ROYCAR71
  • MEMBER
  • 354 POSTS
Hmm I did not know I could run engine with just water for that long. I will try this method since July 4th I have 5 days off. What is RO water?
Was this
answer
helpful?
Yes
No
-1
Wednesday, June 27th, 2012 AT 7:18 PM
Tiny
KHLOW2008
  • MECHANIC
  • 41,815 POSTS
As long as you don't have freezing weather, running without coolant for one or 2 days is ok. RO = reverse osmosis.

If the engine is not running at operating temperature, sludge in system would be stuck and won't be cleared by normal flushing.

When flushing, always use clean water to final flush before adding coolant. Mixing of different brands of coolant can result in clogging of the cooling system, especially the radiator core so you have to flush clean and also after using flushing agents.
Was this
answer
helpful?
Yes
No
-1
Wednesday, June 27th, 2012 AT 8:42 PM
Tiny
ROYCAR71
  • MEMBER
  • 354 POSTS
Back again, I took part of your advice and drove car with just water for a week. I did backflush 3 times during this period. Today I backflushed and put in some prestone radiator cleaner and filled reservoir back up to required level. I drove car around about 2 to 4 hrs. When was about 2 blocks from house my check engine light came on. When at home I let car cool down before checking water color in reservoir. Once cooled I checked and noticed color of water was rusty looking. Is this a bad thing or do I need to reflush and fill water and drive around more until this changes clear? Thanks in advance.
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
Saturday, July 7th, 2012 AT 11:21 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,757 POSTS
The radiator cleaner should have gone in at the beginning of the process, not the end. The goal here is to use the chemical to loosen things up and backflush to carry them away.
Was this
answer
helpful?
Yes
No
+1
Saturday, July 7th, 2012 AT 11:25 PM
Tiny
ROYCAR71
  • MEMBER
  • 354 POSTS
In that case I intend backflush it out and put in just water and drive it around. Then flush again. I just need to know if I am hurting vehicle with just having water in coolant system too long? Thanks.
Was this
answer
helpful?
Yes
No
Saturday, July 7th, 2012 AT 11:32 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,757 POSTS
Short periods of water will not hurt it as long as it is flushed out after. Water is a long period problem. Coolant gets rid of heat better too. Don't leave the chemical in too long (1 day max) as that has a lot of acid in the and will be corrosive if left in.
Was this
answer
helpful?
Yes
No
+1
Saturday, July 7th, 2012 AT 11:36 PM
Tiny
ROYCAR71
  • MEMBER
  • 354 POSTS
As of now I had water in there for about a week. Today I backflushed and just put chemical flush with water. I attend to flush it out again tomorrow. Put in more water and drive around for awhile and backflush Then put in 100 percent universal coolant until I hit fill mark since it is hard to remove all diluted water from engine.
Was this
answer
helpful?
Yes
No
Saturday, July 7th, 2012 AT 11:42 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,757 POSTS
Sounds like a good plan.
Was this
answer
helpful?
Yes
No
Sunday, July 8th, 2012 AT 12:24 AM
Tiny
ROYCAR71
  • MEMBER
  • 354 POSTS
Oh yeah, I forgot to ask. Does it matter what coolant to use Dexcool or universal coolant for O'reilly's?
Was this
answer
helpful?
Yes
No
Sunday, July 8th, 2012 AT 12:46 AM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,757 POSTS
Dexcool would be better. The universal is more for topping off.
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
+1
Sunday, July 8th, 2012 AT 12:48 AM

Please login or register to post a reply.

Related Coolant Reservoir Replace/Remove Content

Coolant Reservoir Replacement
GUIDE
Coolant Reservoir Replacement
The coolant reservoir is used to contain the heated and expanding coolant forced out of the radiator when the engine heats up. This is a natural occurrence, when any liquid...
VIEW MORE

Sponsored links