6 CYLINDER MISFIRE NO/LOW ENERGY PULSE AT INJECTOR FOR 6CYL. WHAT CAN BE THE PROBLEM? GROUND WIRE, ECU?
1993 Lexus SC 300 • 164,000 miles
There is compression in cylinder 6 i think there's no fuel/ or energy coming to the cylinder. I checked for spark plugs/ wires / vacuum leaks still misfires. when I come to a stop sign the whole car is shaking and when I take off from a stop it goes with a vibration
September 28, 2012.
September 28, 2012.
Can my ECU not deliver fuel to cyl 6 properly, can it also create an IDLE to be very low or even stall the engine
I did my ecu is dropping the connection with my tool when i connected the obd2 scanner and even the huge SnapOn diagnostic tool. when I connect the scanner through the diagnostic port on the engine itself or underneath the driver's panel the connection still drops seems like the computer does not want/is not able to send the codes because it is so old and messed up already.
Check for bent pins at ecm or looseconnections. also check for bad connections at aldl. It may be a bad ecm but check to see if #6 is even getting a signal. normally you need a noid light for that though. what is fuel pressure? is it within specs?
There are no bent pins and no loose connections. #6 cyl is getting the power signal to it but it is not getting ground. fuel pressure is fine on the rest of the 5 cyl. but there's no fuel at all in cyl 6 although there seems to be compression going in cyl6 still just no fuel. the fuel injector on #6 is getting low power compared to the rest but no ground response from the ecu. I checked all the possible connections to the injectors, spark plugs, spark plug wires, distributor cap.
try this test although you dont' need to see if theya re working or not. check resistancein #6
1. Start engine. Using a stethoscope, ensure each injector is making a "clicking" noise during operation. If "clicking" noise is not heard, ensure wiring connector is securely fastened.
2. Ensure an injector signal is present on injector harness connector. Turn engine off. Disconnect injector electrical connector. Using a DVOM, measure resistance across injector terminals.
3. Resistance should be approximately 13.8 ohms. If resistance is not as specified, replace fuel injector. Disconnect negative battery cable. Remove injector from engine.
4. Place injector into a container to catch fuel spray. Turn ignition on. DO NOT start engine. Using a jumper wire, connect terminals FP and +B of check connector. See Fig. 13.
Fig. 13: Check Connector Terminal ID (ES300 Shown? Others Similar)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
5. Connect battery voltage to injector terminals for 15 seconds. Ensure an even, cone shaped fuel spray is observed from injector. If fuel spray is not satisfactory, replace injector. If fuel spray is satisfactory, check
volume of fuel delivered by fuel injector.
6. On GS300, fuel volume should be 2.4 3.0 ozs. (70 78 cc) for 15 seconds of operation. On ES300, fuel volume should be 1.8 2.16 ozs. (54 64 cc) for 15 seconds of operation. On LS400 and SC400, fuel
volume should be 1.9 2.4 ozs. (55 70 cc) for 15 seconds of operation. On SC300, fuel volume should be 2.4 3.0 ozs. (70 88 cc) for 15 seconds of operation. Check each injector 2 3 times for volume.
Maximum volume difference between injectors is .16 ozs. (5 cc) for GS300 and ES300, .17 ozs. (10 cc) for SC400 and LS400, and .27 ozs. (9 cc) for SC300. If volume is not satisfactory, replace injector.
7. Remove battery voltage from injector. With injector still placed in container, observe injector tip. If injector drips more than one drop of fuel within one minute, replace fuel injector.
other than that you may have a bad ecu guess it would only be to try one and see if it does same thing. Also have you check main efi relay and fi fuse? and clean ground on back of right rear cylinder head that is the main ground for fuel injectors, ecu etc.
1986 Nissan Stanza, California version. The engine wants to die when stopping. I thought that the lock-up switch for the torque converter was not unlocking. I have installed a used ...
2 answers • 1986 Nissan Sunny • 100,000 miles
1999 Hyundai Elantra mileage: 110,000. This car idles fairly well in neutral or park but very rough in reverse and drive. I just replaced the engine with a used engine and it is doing ...
1 answer • 1999 Hyundai Elantra • 110,000 miles
1988 Chevrolet Astro Van mileage: 247,000. It's time to replace the engine in my 1988 Astro. I bought a 4.3 V6 that has come out of a 1991 S-10. When I dismantled it to get it ready to ...
1 answer • 1988 Chevrolet Astro • 247,000 miles
1990 Toyota Camry mileage: 150,000. 1. The oil warning light is on. 2. There are four quarts of oil in the car. 3. The oil filter is dry. 4. The engine sounds rough. 5. There is noise ...
2 answers • 1990 Toyota Camry • 150,000 miles